Sponsored Content
Full Discussion: HBA card faulty
Operating Systems Linux Red Hat HBA card faulty Post 302919262 by saurabh84g on Tuesday 30th of September 2014 12:23:12 AM
Old 09-30-2014
Hammer & Screwdriver HBA card faulty

Hi,

How to determine if HBA card in getting faulty from linux host ? any pointers.
 

10 More Discussions You Might Find Interesting

1. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

2. Solaris

Qlogic HBA card in E450 with errors

I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
Discussion started by: floydm
9 Replies

3. Solaris

istall sas raid HBA internal card

I need to install a raid HBA internal card on a T5240. The reason is I have more drives and the current mother board controller does not support more than 4 drives. My question is I have raidctl set up on current drives. If I install new HBA card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies

4. Solaris

Install Solaris 10 with an internal StorageTek SAS HBA Raid card

Hi all i would like to ask some suggests about my next job! I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid. The problem come in if every disk is now controlled by the HBA, how can I install the OS? No disk is being detected by the OS. SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies

5. UNIX for Advanced & Expert Users

Sun internal disks and HBA card

I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage. Would I sacrifice performance if I use the same HBA? Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies

6. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies

7. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies

8. Solaris

Extracting HBA Card Hardware info

Hello, I am very new to solaris so please bear with me. I have 2 machines in question. For both I am trying to get the HBA Card Hardware information such as: HBA Model Name HBA Firmware version HBA Port details HBA Driver details First machine is a Solaris 10. When I execute fcinfo... (6 Replies)
Discussion started by: flagman5
6 Replies

9. Solaris

Which FC HBA card support Solaris9

I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage. in OK prompt, PROBE-SCSI-ALL showing A5000 fc hdds details in ok prompt..... but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies

10. Solaris

Solaris 10: how to disable an unused HBA card

Dear all, I have a new Oracle Blade X4-2B server, running Solaris 10. The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing. My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
HBA_GetBindingCapability(3HBAAPI)	      Common Fibre Channel HBA Information Library Functions		 HBA_GetBindingCapability(3HBAAPI)

NAME
HBA_GetBindingCapability, HBA_GetBindingSupport, HBA_SetBindingSupport - return and sets binding capabilities on an HBA port SYNOPSIS
cc [ flag... ] file... -lHBAAPI [ library... ] #include <hbaapi.h> HBA_HANDLE HBA_GetBindingCapability(HBA_HANDLE handle, HBA_WWN hbaPortWWN, HBA_BIND_CAPABILITY *pFlags); HBA_STATUS HBA_GetBindingSupport(HBA_HANDLE handle, HBA_WWN hbaPortWWN, HBA_BIND_CAPABILITY *pFlags); void HBA_SetBindingSupport(HBA_HANDLE handle, HBA_WWN hbaPortWWN, HBA_BIND_CAPABILITY Flags); PARAMETERS
handle an open handle returned from HBA_OpenAdapter(3HBAAPI) hbaPortWWN the Port WWN of the local HBA through which the binding capabilities implemented by the HBA is returned pFlags a pointer to an HBA_BIND_CAPABILITY structure that returns the persistent binding capabilites implemented by the HBA Flags an HBA_BIND_CAPABILITY structure containing the persistent binding capabilites to enable for the HBA DESCRIPTION
The HBA_GetBindingCapability() function returns the binding capabilities implemented by the HBA. The HBA_GetBindingSupport() function returns the currently enabled binding capabilities for the HBA. The HBA_SetBindingSupport() function sets the currently enabled binding capabilites for the HBA to a subset of the binding capabilities implemented by the HBA. RETURN VALUES
The HBA_GetBindingCapability() and HBA_GetBindingSupport() functions return the following values: HBA_STATUS_OK Persistent binding capabilites have been returned. HBA_STATUS_ERROR_ILLEGAL_WWN Port WWN hbaPortWWN is not a WWN contained by the HBA referenced by handle. HBA_STATUS_ERROR_NOT_SUPPORTED The HBA handle specified by handle does not support persistent binding. HBA_STATUS_ERROR An error occurred. The value of pFlags remains unchanged and points to the persistent binding capabilites. The HBA_SetBindingSupport() function returns: HBA_STATUS_OK Persistent binding capabilites have been enabled. HBA_STATUS_ERROR_ILLEGAL_WWN Port WWN hbaPortWWN is not a WWN contained by the HBA referenced by handle. HBA_STATUS_ERROR_NOT_SUPPORTED The HBA handle specified by handle does not support persistent binding. HBA_STATUS_ERROR_INCAPABLE The flags argument contains a capability not implemented by the HBA. HBA_STATUS_ERROR An error occurred. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Interface Stability |Standard: FC-MI 1.92 (API | | |version 1) | +-----------------------------+-----------------------------+ | |Standard: FC-HBA Version 4 | | |(API version 2) | +-----------------------------+-----------------------------+ |MT-Level |Safe | +-----------------------------+-----------------------------+ SEE ALSO
libhbaapi(3LIB), attributes(5) T11 FC-MI Specification SunOS 5.10 1 Sep 2003 HBA_GetBindingCapability(3HBAAPI)
All times are GMT -4. The time now is 06:24 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy