Depends if you are using ZFS / UFS with metasets setup can vary in steps.
If you are using ZFS, present the disks to new nodes and check first cldev output if both disk are visible for both nodes of the cluster.
Create a zpool out of those disks, you don't have to use DID devices.
After that run :
Where 'zpool-list' is list of existing zpools that resource manages + your new pool, comma separated.
hastorageplus will import the pool and mount it after adding.
Administration of newly added zpool (creating zfs filesystems and their mountpoints) is done with zfs commands.
If you are using metasets things are a bit more complicated but fairly well documented.
Anyone know of a guide or instructions for Solaris
I got to configure a SBUS HBA to talk to a tape robot.
I have done this on a switch but not point to point.
just going HBA >>>>> TAPE Fibre simple two nodes
Kie (6 Replies)
I have rcently setup a 4 node cluster running sun cluster 3.2
and I have installed 4 zones on each node. when installing the zones I had to install the zone on all nodes the on the last node do a zlogin -C <zonename>
this worked ok.
theni I tried to siwitch the zone to node a thei work... (14 Replies)
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
have a pair of sun servers, wanting to test drive a
2-node cluster using both software..
would like disable one of these cluster software while the othe is running..
Is it feasible at all ?? (2 Replies)
Hello. I am Running AIX 6.1 and PowerHA 6.1
I have an active/active cluster (Prod/Dev) cluster. Each side will failover to the other.
I have on my prod side an active volume group with a file system. The VG is imported on both nodes and active (varried on, file system mounted) on the prod... (3 Replies)
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Hi,
What is the procedure require to add the luns to the mount point in linux server.
say for example due to lack of space in the mount point /u03,i want to add
some extra 20gb space to mount point, how to add that ?
What does luns means ?
Regards,
Maddy (5 Replies)
What's the best way clusters for Storage at some point? (The way that data is the same in all parts)
To set up a Web server cluster is the logical way?!
Cluster database and Storage and then by keepalived + HA cluster will be communicated?
Or, there a better solution? (For about 4 points)
Thank... (0 Replies)
How to create a new mount point with 600GB and add 350 GBexisting mount point
Best if there step that i can follow or execute before i mount or add diskspace IN AIX
Thanks (2 Replies)
Discussion started by: Thilagarajan
2 Replies
LEARN ABOUT CENTOS
amzfs-sendrecv
AMZFS-SENDRECV(8) System Administration Commands AMZFS-SENDRECV(8)NAME
amzfs-sendrecv - Amanda script to create zfs sendrecv
DESCRIPTION
amzfs-sendrecv is an Amanda application implementing the Application API. It should not be run by users directly. It create a zfs snapshot
of the filesystem and backup the snapshot with 'zfs send'. Snapshot are kept after the backup is done, this increase the disk space use on
the client but it is neccesary to be able do to incremental backup. If you want only full backup, you can disable this feature by setting
the KEEP-SNAPSHOT property to 'NO'. Only the restoration of the complete backup is allowed, it is impossible to restore a single file.
The application is run as the amanda user, it must have many zfs priviledge:
zfs allow -ldu AMANDA_USER mount,create,rename,snapshot,destroy,send,receive FILESYSTEM
Some system doesn't have "zfs allow", but you can give the Amanda backup user the rights to manipulate ZFS filesystems by using the
following command:
usermod -P "ZFS File System Management,ZFS Storage Management" AMANDA_USER
This will require that your run zfs under pfexec, set the PFEXEC property to YES.
The format of the diskdevice in the disklist (DLE) must be one of:
Desciption Example
-----------------
Mountpoint /data
ZFS pool name datapool
ZFS filesystem datapool/database
ZFS logical volume datapool/dbvol
The filesystem doesn't need to be mounted.
PROPERTIES
This section lists the properties that control amzfs-sendrecv's functionality. See amanda-applications(7) for information on the
Application API, application configuration.
DF-PATH
Path to the 'df' binary, search in $PATH by default.
KEEP-SNAPSHOT
If "YES" (the default), snapshot are kept after the backup, if set to "NO" then snapshot are no kept and incremental backup will fail.
ZFS-PATH
Path to the 'zfs' binary, search in $PATH by default.
PFEXEC-PATH
Path to the 'pfexec' binary, search in $PATH by default.
PFEXEC
If "NO" (the default), pfexec is not used, if set to "YES" then pfexec is used.
EXAMPLE
In this example, a dumptype is defined to use amzfs-sendrecv application to backup a zfs filesystem.
define application-tool amzfs_sendrecv {
comment "amzfs-sendrecv"
plugin "amzfs-sendrecv"
#property "DF-PATH" "/usr/sbin/df"
#property "KEEP-SNAPSHOT" "YES"
#property "ZFS-PATH" "/usr/sbin/zfs"
#property "PFEXEC-PATH" "/usr/sbin/pfexec"
#property "PFEXEC" "NO"
}
define dumptype user-zfs-sendrecv {
program "APPLICATION"
application "amzfs_sendrecv"
}
SEE ALSO amanda(8), amanda.conf(5), amanda-client.conf(5), amanda-applications(7)
The Amanda Wiki: : http://wiki.zmanda.com/
AUTHOR
Jean-Louis Martineau <martineau@zmanda.com>
Zmanda, Inc. (http://www.zmanda.com)
Amanda 3.3.3 01/10/2013 AMZFS-SENDRECV(8)