You and me both, just for completeness - here are the guts of the logger.sh script that all my scripts call to log to a single journal/log file for the day.
This just allows multiple scripts to log as required - all to the same output file - handy for error checking etc.
Hi All ,
I try to install some packages in my global zone...
On the execution of the installion of the script it quits by saying the error
"Non global zone check failed"
Kindly help me in this regard
Thanks in advance,
jeganr (7 Replies)
I have configured three zones on Solaris-11. These are non-global zones contain Solaris-11 only. One of the zone is not booting up, complaining about IP address in use, while it is not.
root@tdpdmsp02 # zoneadm list -icv
ID NAME STATUS PATH BRAND IP... (3 Replies)
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
Am new on Solaris
If I compare with ESXi default timezone is UTC and we have to set BIOS timezone to UTC too .
What we follow and best practice in Solaris Sparc servers .
Thanks in advance . (2 Replies)
I can't compile anything, the final make error says "Command failed for target `install-recursive'", but I am not able to identify the root cause of that error, I tried with cc, gcc 4.5, also gcc 5.2, using make, using gmake 3.82, ld 5.11, gld 2.31... and I am totally stuck yet... please help, to... (4 Replies)
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT CENTOS
doveadm-log
DOVEADM-LOG(1) Dovecot DOVEADM-LOG(1)NAME
doveadm-log - Locate, test or reopen Dovecot's log files
SYNOPSIS
doveadm [-Dv] log errors [-s min_timestamp]
doveadm [-Dv] log find [directory]
doveadm [-Dv] log reopen
doveadm [-Dv] log test
DESCRIPTION
The doveadm log commands are used to locate and reopen the log files of dovecot(1). It's also possible to test the configured targets of
the *log_path settings.
OPTIONS
Global doveadm(1) options:
-D Enables verbosity and debug messages.
-v Enables verbosity, including progress counter.
COMMANDS
log errors
doveadm log errors [-s min_timestamp]
The log errors command is used to show the last - up to 1,000 - errors and warnings. If no output is generated, no errors have occurred
since the last start.
-s min_timestamp
An integer value, representing seconds since the epoch - also known as Unix timestamp. When a min_timestamp was given, doveadm(1)
will only show errors occurred since that point in time.
log find
doveadm log find [directory]
The log find command is used to show the location of the log files, to which dovecot(1) sends its log messages. If dovecot(1) logs its
messages through syslogd(8) and doveadm(1) could not find any log files, you can specify the directory where your syslogd writes its log
files.
log reopen
doveadm log reopen
This command causes doveadm to reopen all log files, configured in the log_path, info_log_path and debug_log_path settings. These settings
are configured in /etc/dovecot/conf.d/10-logging.conf.
This is for example useful after manually rotating the log files.
log test
doveadm log test
This command causes doveadm to write the message "This is Dovecot's priority log (timestamp)" to the configured log files. The used prior-
ities are: debug, info, warning, error and fatal.
EXAMPLE
This example shows how to locate the log files used by dovecot(1).
doveadm log find
Looking for log files from /var/log
Debug: /var/log/dovecot.debug
Info: /var/log/mail.log
Warning: /var/log/mail.log
Error: /var/log/mail.log
Fatal: /var/log/mail.log
REPORTING BUGS
Report bugs, including doveconf -n output, to the Dovecot Mailing List <dovecot@dovecot.org>. Information about reporting bugs is avail-
able at: http://dovecot.org/bugreport.html
SEE ALSO doveadm(1)Dovecot v2.2 2013-11-24 DOVEADM-LOG(1)