08-29-2014
Hi Eprlsguy,
Can you post the output of the "zpool list" and the "zpool status" commands.
Regards
Dave
Last edited by rbatte1; 08-29-2014 at 10:21 AM..
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Need some advice and guidance for this UNIX beginner. Due to downsizing I have inherited the SysAdmin duties..(sigh). Please excuse and forgive me if I use the wrong terms below....
Situation:
We have UNIX ( Solaris 7/8/9( it varies) on Sun Ultra 10's) servers located at several global... (1 Reply)
Discussion started by: HikerLT
1 Replies
2. Solaris
I have gone over some articles regarding zones, I haven't found one that gives the exact information I'm looking for. I think I'm close though.
I have 2 servers, each with a HBA into a SAN, they are both presented with the same luns.
On server1, configured and installed the zone (zone1), the... (6 Replies)
Discussion started by: beaker457
6 Replies
3. Solaris
friends,
Suppose I am typing metastat command and it is showing:
d100: Concat/Stripe
Size: 369495 blocks (180 MB)
Stripe 0: (interlace: 32 blocks)
Device Start Block Dbase Reloc
c1d0s0 16065 Yes Yes
c1d0s1 0 No Yes... (4 Replies)
Discussion started by: saagar
4 Replies
4. UNIX for Advanced & Expert Users
I have several Solaris 8,9 and 10 servers.
I need to refresh them and avoid doing any OS upgrades. I may have to apply patches when I am done due to the new hardware.
My current servers have internal disk and my new target servers (same processor types) will have only SAN storage. Once the... (0 Replies)
Discussion started by: zzqv9p
0 Replies
5. UNIX for Advanced & Expert Users
Hi All!
I'm running Solaris 8(02/02) on a v880 with 6 internal drives and several SAN drives attached via HBA cards.
My questions is this: Can I use devfsadm -C to see new SAN drives without rebooting?
Thanks!! (2 Replies)
Discussion started by: bluescreen
2 Replies
6. Solaris
Dear All,
I have been trying to move my existing Solaris Installation (x86, 10/08) to a bigger HDD.
So I created a 22 cylinder boot partition and used the rest of the space for a Solaris2 partition. Then I created slices same size like on my current disk.
I copied all files with cpio and... (3 Replies)
Discussion started by: BigT79
3 Replies
7. Solaris
Hello and let me say at first, thank you for viewing this problem I have.
From the top!
Where I work, we have a Dell PowerEdge T300 X86 system running Solaris 10 8/07 s10x_u4wos_12b X86, and we realized, if this machine went down, we would be in trouble. So to fix that situation, I took it... (5 Replies)
Discussion started by: nitrolinux
5 Replies
8. Solaris
Hello,
What is the best method to use to clone a Solaris 10 machine with zones, to ensure all software and config can be easily installed on new hardware?
Thank You (4 Replies)
Discussion started by: da2013
4 Replies
9. Solaris
Hi all,
I am trying to use archiveadm to backup/clone an existing Solaris11.4 system.
However, i failed at media creation with the error -> "Media can only be created from archives containing root-only data"
root@xxx:/mnt/opt/software# zpool list
NAME SIZE ALLOC FREE CAP DEDUP ... (6 Replies)
Discussion started by: javanoob
6 Replies
LEARN ABOUT FREEBSD
hptmv
HPTMV(4) BSD Kernel Interfaces Manual HPTMV(4)
NAME
hptmv -- HighPoint RocketRAID 182x device driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device hptmv
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
hptmv_load="YES"
DESCRIPTION
The hptmv driver provides support for HighPoint's RocketRAID 182x based RAID controller.
These devices support ATA disk drives and provide RAID0 (striping), RAID1 (mirroring), and RAID5 functionality.
HARDWARE
The hptmv driver supports the following ATA RAID controllers:
o HighPoint's RocketRAID 182x series
NOTES
The hptmv driver only works on the i386 and amd64 platforms as it requires a binary blob object from the manufacturer which they only supply
for these platforms. The hptmv driver does not work on i386 with pae(4) enabled.
SEE ALSO
kld(4), kldload(8), loader(8)
HISTORY
The hptmv device driver first appeared in FreeBSD 5.3.
AUTHORS
The hptmv device driver was written by HighPoint Technologies, Inc., and ported to FreeBSD by Scott Long. This manual page was written by
David E. O'Brien.
BUGS
The hptmv driver does not support manipulating the RAID from the OS, RAIDs need to be set up from the on-board BIOS.
BSD
November 17, 2005 BSD