08-29-2014
Hi Eprlsguy,
Can you post the output of the "zpool list" and the "zpool status" commands.
Regards
Dave
Last edited by rbatte1; 08-29-2014 at 10:21 AM..
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Need some advice and guidance for this UNIX beginner. Due to downsizing I have inherited the SysAdmin duties..(sigh). Please excuse and forgive me if I use the wrong terms below....
Situation:
We have UNIX ( Solaris 7/8/9( it varies) on Sun Ultra 10's) servers located at several global... (1 Reply)
Discussion started by: HikerLT
1 Replies
2. Solaris
I have gone over some articles regarding zones, I haven't found one that gives the exact information I'm looking for. I think I'm close though.
I have 2 servers, each with a HBA into a SAN, they are both presented with the same luns.
On server1, configured and installed the zone (zone1), the... (6 Replies)
Discussion started by: beaker457
6 Replies
3. Solaris
friends,
Suppose I am typing metastat command and it is showing:
d100: Concat/Stripe
Size: 369495 blocks (180 MB)
Stripe 0: (interlace: 32 blocks)
Device Start Block Dbase Reloc
c1d0s0 16065 Yes Yes
c1d0s1 0 No Yes... (4 Replies)
Discussion started by: saagar
4 Replies
4. UNIX for Advanced & Expert Users
I have several Solaris 8,9 and 10 servers.
I need to refresh them and avoid doing any OS upgrades. I may have to apply patches when I am done due to the new hardware.
My current servers have internal disk and my new target servers (same processor types) will have only SAN storage. Once the... (0 Replies)
Discussion started by: zzqv9p
0 Replies
5. UNIX for Advanced & Expert Users
Hi All!
I'm running Solaris 8(02/02) on a v880 with 6 internal drives and several SAN drives attached via HBA cards.
My questions is this: Can I use devfsadm -C to see new SAN drives without rebooting?
Thanks!! (2 Replies)
Discussion started by: bluescreen
2 Replies
6. Solaris
Dear All,
I have been trying to move my existing Solaris Installation (x86, 10/08) to a bigger HDD.
So I created a 22 cylinder boot partition and used the rest of the space for a Solaris2 partition. Then I created slices same size like on my current disk.
I copied all files with cpio and... (3 Replies)
Discussion started by: BigT79
3 Replies
7. Solaris
Hello and let me say at first, thank you for viewing this problem I have.
From the top!
Where I work, we have a Dell PowerEdge T300 X86 system running Solaris 10 8/07 s10x_u4wos_12b X86, and we realized, if this machine went down, we would be in trouble. So to fix that situation, I took it... (5 Replies)
Discussion started by: nitrolinux
5 Replies
8. Solaris
Hello,
What is the best method to use to clone a Solaris 10 machine with zones, to ensure all software and config can be easily installed on new hardware?
Thank You (4 Replies)
Discussion started by: da2013
4 Replies
9. Solaris
Hi all,
I am trying to use archiveadm to backup/clone an existing Solaris11.4 system.
However, i failed at media creation with the error -> "Media can only be created from archives containing root-only data"
root@xxx:/mnt/opt/software# zpool list
NAME SIZE ALLOC FREE CAP DEDUP ... (6 Replies)
Discussion started by: javanoob
6 Replies
SBP(4) BSD Kernel Interfaces Manual SBP(4)
NAME
sbp -- Serial Bus Protocol 2 (SBP-2) Mass Storage Devices driver
SYNOPSIS
kldload firewire
kldload cam
kldload sbp
or
device sbp
device firewire
device scbus
device da
device cd
device pass
DESCRIPTION
The sbp driver provides support for SBP-2 devices that attach to the FireWire (IEEE 1394) port. It should work with SBP-2 devices which the
CAM layer supports, for example, HDDs, CDROM drives and DVD drives.
Some users familiar with umass(4) might wonder why the device is not detached at the CAM layer when the device is unplugged. It is detached
only if the device has not been plugged again during several bus resets. This is for preventing to detach an active file system even when
the device cannot be probed correctly for some reason after a bus reset or when the device is temporary disconnected because the user changes
the bus topology. If you want to force to detach the device, run ``fwcontrol -r'' several times or set hw.firewire.hold_count=0 by
sysctl(1).
Some (broken) HDDs do not work well with tagged queuing. If you have problems with such drives, try ``camcontrol [device id] tags -N 1'' to
disable tagged queuing.
SEE ALSO
cam(4), firewire(4), camcontrol(8), fwcontrol(8), kldload(8), sysctl(8)
AUTHORS
The sbp driver was written by Katsushi Kobayashi and Hidetoshi Shimokawa.
This manual page was written by Katsushi Kobayashi.
BSD
May 20, 2002 BSD