08-07-2014
Sounds like a problem with your router/modem dropping packets. DNS, which IIRC uses UDP, is going to be hurt hard by that.
When's the last time the router or the modem were rebooted?
10 More Discussions You Might Find Interesting
1. Cybersecurity
At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer??
If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
0 Replies
2. IP Networking
Hi,
I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled.
I can connect to the access point from the laptop, but how do I get the... (1 Reply)
Discussion started by: perleo
1 Replies
3. UNIX for Dummies Questions & Answers
I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris.
i did not... (0 Replies)
Discussion started by: stakes20
0 Replies
4. Linux
I am running FC4:
Linux maincomp 2.6.13-1.1532_FC4smp
I recently changed the OS from windows XP, and have a feeling that for some reason my wireless network card is slower on Fedora Core 4. The Belkin PCI 802.11b card was automatically detected and configured by FC4 when I installed the OS,... (0 Replies)
Discussion started by: dangral
0 Replies
5. Cybersecurity
Hi all,
How can I monitor packet traffic on my wireless router?
Some info
- my wireless router is netgear wgr614
- everyone can connect it i.e. no password required
- I would like to see where they connect, how they are using the internet connection
I installed wireshark and captured... (3 Replies)
Discussion started by: SaTYR
3 Replies
6. Hardware
hi
Howto identify wireless network card using Live CD? (2 Replies)
Discussion started by: ccc
2 Replies
7. Ubuntu
Hi,
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies
8. Red Hat
Hi,
I am trying to set up a wireless internet connection on my centos OS (6). I can connect via the copper using the internal LAN but cannot get the wireless connection working.
The 2 files that I have configured are:
My wpa_supplicant.conf:
ctrl_interface=/var/run/wpa_supplicant... (1 Reply)
Discussion started by: Duffs22
1 Replies
9. Hardware
Good Day All,
There are numerous results when searching google on this issue, however, none seem to have a solution.
I have read until my eyes bleed and banged my head on the table more than once! :)
I am hoping to resolve this issue -- or at least have a decent workaround.
It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies
10. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
LEARN ABOUT HPUX
map-mbone
map-mbone(1M) map-mbone(1M)
NAME
map-mbone - Multicast Router Connection Mapper
SYNOPSIS
debuglevel] retries] timeout] [multicast-router]
DESCRIPTION
requests the multicast router connection information from the multicast-router, and prints the information to the standard out. sends out
the ASK_NEIGHBORS igmp message to the multicast-router. When the multicast-router receives the request, it sends back its configuration
information. multicast-router can be either an ip address or a system name.
If the multicast-router is not specified, flood mode is on by default and the igmp request message is sent to all the multicast router on
the local network. With flood mode on, when finds new neighbor routers from the replies, it will send the same igmp request to the new
neighbor routers. This activity continues until no new neighbor routers are reported in the replies.
The command line options are:
Sets the level for printing out the debug message. The default is 0,
which prints only error and warning messages. Debug level three prints most the messages.
Sets the retry times to poll the routing daemon for information. The
default is 1.
It specifies the timeout value in seconds for waiting the reply. The
default value is 2 seconds.
Sets the flood mode on. It is the default value when no multicast-router is given on the command line input.
Generates output in GRaphEd format.
Disable DNS lookup for the multicast router names.
The output contains the interface configuration information of the requested router(s). The format for each interface output is:
If there are multiple neighbor routers on one interface, they will all be reported. The neighbor_name will not be printed if the option is
specified on the command line.
The possible values for are:
Neighbors are reached via tunnel.
The tunnel uses IP source routing.
The interface is down.
The interface is administratively disabled for multicast routing.
The local router is the querier of the subnet.
The format of the GRaphEd output is:
If there is no neighbor router on an interface, then a will be put next to the node_name. If there are multiple neighbor routers on one
interface, all of them will be reported. The possible values for are:
The neighbor is reached via tunnel.
The neighbor is on the same network/subnet.
The interface is down.
Please see mrouted(1M) for and
EXAMPLES
Querying for the multicast router connection information.
127.0.0.1 (localhost) [version 3.3]:
193.2.1.39 -> 0.0.0.0 (all-zeros-broadcast) [1/1/disabled]
15.13.106.144 -> 15.255.176.33 (matmos.hpl.hp.com) [10/1/tunnel]
15.13.106.144 -> 15.17.20.7 (hpspddc.vid.hp.com) [10/1/tunnel/down]
Querying for multicast router connectivity with option:
GRAPH "Multicast Router Connectivity: Wed Feb 1 17:34:59 1995"=UNDIRECTED
252537488 {$ NP 1440 1060 $} "hpntc1t.cup.hp.com*"
;
252538974 {$ NP 940 1120 $} "hpntcbs.cup.hp.com"
252537488 "10/1E"
252539807 "1/1P"
;
252539807 {$ NP 1590 1150 $} "hpntc1h.cup.hp.com*"
;
Note
must be run as root.
AUTHOR
was developed by Pavel Curtis.
SEE ALSO
mrouted(1M), mrinfo(1M).
map-mbone(1M)