Sponsored Content
Operating Systems Solaris How to increase the e1000g0 interface speed in Solaris? Post 302911848 by gsrungav on Monday 4th of August 2014 05:38:45 AM
Old 08-04-2014
How to increase the e1000g0 interface speed in Solaris?

Hi All,

Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?.

Thanks and Regards,
Ganesh.

Last edited by rbatte1; 08-11-2014 at 09:02 AM.. Reason: Spelling
 

10 More Discussions You Might Find Interesting

1. Post Here to Contact Site Administrators and Moderators

Anybody Notice a Speed Increase?

Hi. I moved this site to a T3 facility and wanted to know if any of the long time users noticed a performance improvement? Thanks, Neo. (5 Replies)
Discussion started by: Neo
5 Replies

2. Solaris

how to force e1000g0 interface in solaris 10

Hi all, I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot. But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands. ... (1 Reply)
Discussion started by: mailbox80
1 Replies

3. Cybersecurity

how to increase the speed of sftp

hi , i have to tranfer some 12 - 13 gb of files from one server to anothier presently i m using the SFTP but it is taking to much time to trafer the files is there any way to use increase the efficiency of SFTP. i cant use the FTP (4 Replies)
Discussion started by: narang.mohit
4 Replies

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

5. Solaris

hba speed Solaris 9

Hello, In Solaris 10 I can use fcinfo to find what speed the hba ports are running at, am I able to find this out using Solaris 9? I have tried a few variations on luxadm but cant find anything relevant. Thanks. (1 Reply)
Discussion started by: Actuator
1 Replies

6. Red Hat

Increase speed in linux server

Hi, Will removing space from the server increases the speed/performance. how are they related? please explain the relationship. thanks in advance regards, Pradeep (2 Replies)
Discussion started by: pradebban
2 Replies

7. Solaris

Solaris SPARC speed issue

Hello helpful Unix gurus! First, I appreciate any help I can get. I have a product that we have ported (for years now) on Solaris SPARC 7.x OS from 1998 (or around that time I guess) that is compiled to a 32 executable. It has run (with various modifications over the years) on any Solaris... (10 Replies)
Discussion started by: Pug
10 Replies

8. UNIX for Advanced & Expert Users

How to increase executions speed of loops.?

(2 Replies)
Discussion started by: Venkatesh1
2 Replies

9. Solaris

Interface e1000g0 not showing in running state

Hello all, I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0. This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help. Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies

10. AIX

AIX 4.2 increase ethernet speed

Hello. I have a server RS/6000 with AIX 4.2. The server have a network card with 10/100mbps speed, but for some reason, the ethernet only runs at 10Mbps, it doesn,t matter if I put the net cable on a 100Mbps switch, it keeps running at 10Mbps speed.... I know how to view/change ethernet speed... (1 Reply)
Discussion started by: little_ball
1 Replies
TXP(4)							   BSD Kernel Interfaces Manual 						    TXP(4)

NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device txp Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_txp_load="YES" DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset. Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4) checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload- ing, tcp(4) segmentation, nor ipsec(4) acceleration. When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex. The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are: media autoselect Attempt to autoselect the media type (default) media 100baseTX mediaopt full-duplex Use 100baseTX, full duplex media 100baseTX [mediaopt half-duplex] Use 100baseTX, half duplex media 10baseT mediaopt full-duplex Use 10baseT, full duplex media 10baseT [mediaopt half-duplex] Use 10baseT, half duplex HARDWARE
The txp driver supports the following cards: o 3Com 3CR990-TX-95 o 3Com 3CR990-TX-97 o 3Com 3cR990B-TXM o 3Com 3CR990SVR95 o 3Com 3CR990SVR97 o 3Com 3cR990B-SRV SEE ALSO
altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8) HISTORY
The txp driver first appeared in OpenBSD 2.9. BSD
January 26, 2012 BSD
All times are GMT -4. The time now is 01:10 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy