Sponsored Content
Full Discussion: VXVM in POWERHA 6.1
Operating Systems AIX VXVM in POWERHA 6.1 Post 302911201 by ibmtech on Wednesday 30th of July 2014 01:51:06 PM
Old 07-30-2014
I am wondering why in the world are you using vxvm with HACMP? veritas has is own clustering software.

Since its not using native logical volume manager, I doubt it will work smoothly.

You may need to install some additional software packages for HACMP to undertake vxvm as its local LVM.

Best is open a call with IBM and ask them.
 

10 More Discussions You Might Find Interesting

1. AIX

strange route issue in powerha 5.4?

hi all we upgraded hacmp(powerha) from 5.2 to 5.4 recently . during the failover testing, we found a strange network issue. after standby node took service ip address (172.15.100.8) online at standby NIC, we were able to log in the standby node by telnet 172.15.100.8 which stays at... (1 Reply)
Discussion started by: rs6000er
1 Replies

2. AIX

PowerHA - assistant can't find network

I've configured multiple clusters using PowerHA 5.5, but never using the 'Two-node cluster configuration assistant'. I removed all the clusters, clean setup, and gave the assistant a try. I've filled in all the necessary options: Communication Path to Takeover Node Application Server ... (11 Replies)
Discussion started by: Koen87
11 Replies

3. AIX

PowerHA, same subnet for persistent and service ip

I am new in AIX and please forgive my poor english. I know that AIX allow same subnet IPs for different interfaces, which result in multipath routing / route striping. My question is, is there any best practice for the persistent and service IP with same subnet to stay on same interface, or... (5 Replies)
Discussion started by: skeyeung
5 Replies

4. AIX

PowerHA Disk on VIO Server

Hello AIX GURU's Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server? my questions are: 1. Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar? or 2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies

5. AIX

PowerHA with 3rd node for communication

Looking to find PowerHA with 3rd node used for communication (voting node) only. Does anyone use such configuration with IBM products? (2 Replies)
Discussion started by: gogogo
2 Replies

6. AIX

PowerHA HACMP on VIOS servers

Few questions regarding Power HA ( previously known as HACMP) and VIOS POWERVM IVM ( IBM Virtualization I/O Server ) Is it possible to create HACMP cluster between two VIOS servers Physical Machine_1 VIOS_SERVER_1 LPAR_1 SHARED_DISK_XX VIOS_SERVER_2 Physical Machine_2 LPAR_2... (6 Replies)
Discussion started by: filosophizer
6 Replies

7. AIX

Powerha on AIX 6.1.9

hello ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415 work with dmx4 EMC storgae. after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine : hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies

8. AIX

PowerHA; Import flash copy of VG?

Hey guys, wondering if this is possible to accomplish. PowerHA SystemMirror7.1 active/passive cluster. Restored a clustered system in test and upgraded to the latest version of PowerHA. Things are working great. However in the interest of time during cut over to the new system, I was hoping to... (4 Replies)
Discussion started by: j_aix
4 Replies

9. AIX

PowerHa 7.1 Migration check failed

Hello Guys, I was trying to upgrade the PowerHA from 6.1.0.9 to 7.1.3 in prod cluster. Have snapshot migration and run climgcheck. 1. Run climgcheck on node1(kul1pqcmur01) and it success 2. Upgrade the cluster sw 3. Run climgcheck on node2(kul1pqcmur02) and it failed with below errors ... (6 Replies)
Discussion started by: novaothers
6 Replies

10. AIX

Upgrading PowerHA from 7.1.0 to 7.1.3

Hi All, As per the IBM upgrade/support matrix IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ... 1 ) Bring down the cluster 2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LVREMOVE(8)						      System Manager's Manual						       LVREMOVE(8)

NAME
lvremove - remove a logical volume SYNOPSIS
lvremove [-A|--autobackup {y|n}] [-d|--debug] [-f|--force] [-h|--help] [-v|--verbose] LogicalVolumePath [LogicalVolumePath...] DESCRIPTION
lvremove allows you to remove one or more inactive logical volumes. OPTIONS -A, --autobackup y/n Controls automatic backup of VG metadata after the change ( see vgcfgbackup(8) ). Default is yes. -d, --debug Enables additional debugging output (if compiled with DEBUG). -f, --force Force remove without confirmation. -h, --help Print a usage message on standard output and exit successfully. -v, --verbose Gives verbose runtime information about lvremove's activities. Example "lvremove -f /dev/vg00/lvol1" removes that inactive logical volume unconditionally. DIAGNOSTICS
lvremove returns an exit code of 0 for success and > 0 for error: 1 no logical volume name on command line 2 invalid logical volume name 3 error checking existence of volume group 4 inactive volume group 5 error getting VGDA from kernel 6 error getting status of logical volume from kernel 7 open logical volume cannot be removed 8 error reading VGDA 9 error removing logical volume from VGDA 10 error removing logical volume from kernel 11 error writing VGDA to physical volume(s) 95 driver/module not in kernel 96 invalid I/O protocol version 97 error locking logical volume manager 98 invalid lvmtab (run vgscan(8)) 99 invalid command line ENVIRONMENT VARIABLES
LVM_AUTOBACKUP If this variable is set to "no" then the automatic backup of VG metadata is turned off. LVM_VG_MAX_BACKUPS This variable determines the backup history depth of kept VGDA copy files in /etc/lvmconf. It can be set to a positive number between 0 and 999. The higher this number is, the more changes you can restore using vgcfgrestore(8). LVM_VG_NAME The default Volume Group Name to use. Setting this variable enables you to enter just the Logical Volume Name rather than its com- plete path. See also lvm(8), lvcreate(8), lvdisplay(8), lvscan(8) AUTHOR
Heinz Mauelshagen <Linux-LVM@Sistina.com> Heinz Mauelshagen LVM TOOLS LVREMOVE(8)
All times are GMT -4. The time now is 01:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy