07-24-2014
Then why is my telnet connecting (or appearing to)?
Who says I am brute-force-scanning all these ports, I am testing specific IP addresses and ports over a VPN to a real-time application service that I need to ensure 24/5 availability on.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there, I've an stupid question. If I make a telnet to a server from my computer and then execute a command that starts an application (on the server), when I disconnect, the application stops running, which is pretty obvious. Is it possible to add a flag at the end of the command so when I cut... (4 Replies)
Discussion started by: piltrafa
4 Replies
2. Programming
Hi Folks
I am not a c programmer .But i need help in writing a program which can do this any ideas on how to go about it .
i start a server on the target server where files need to be copied
start-server -port 5006 & ---start the server and listen it on a partcular port
on the source... (2 Replies)
Discussion started by: linuxdba
2 Replies
3. UNIX for Advanced & Expert Users
I'd like to do a data transfer without encryption but with a guarantee that my data comes from a legit source. I'm thinking something that uses a public key scheme to sign the data.
Does anyone know of something like that?
Thanks!
-Pileofrogs (1 Reply)
Discussion started by: pileofrogs
1 Replies
4. Shell Programming and Scripting
Is there a way how to react on the message a client sent to the server?
I would like as the client sent message to server: "get information such and such" and server would answer.
Thank you for reply! (6 Replies)
Discussion started by: MartyIX
6 Replies
5. Solaris
hello guys, i want to install netcat on my solaris. after i tar and gunzip netcat i'm confuse what do i must to do ? please help me to install netcat on my solaris. I'm beginner :( (2 Replies)
Discussion started by: praset
2 Replies
6. Linux
Hello,
Thank you very much for the line nc -lp <port> . I tried to run simple chat session with nc as it's shown in catonmatDOTorg but failed miserably with that syntax inspite of opening port 7777 by iptables . But your command example is working nicely.
So a bagful of thanks :))
Only one... (0 Replies)
Discussion started by: vectrum
0 Replies
7. Shell Programming and Scripting
Hi;
I have a url like
http://localhost:8080/examples/jsp/dates/nextPageToPost.jsp?name=ajay&password=pas&sex=Male&check=on&nationality=USA&description=aa&submit=submit
in which i want to use nc for http post for parameters like "name","password"....etc
can neone please help me how to do that... (3 Replies)
Discussion started by: ajaypadvi
3 Replies
8. IP Networking
Hi all,
I know my question is regarding Windows and not Linux, but I simply need people who know Netcat pretty well and I'm guessing here is a good place for that. So on with my question.
I'm doing some research, and I was playing around with netcat on a WinXP VM but I can't seem to get... (0 Replies)
Discussion started by: MrCrumbs
0 Replies
9. Shell Programming and Scripting
Hi
Need help to connect from Ubuntu to Windows using NetCat nc
I can not get my script to send new-line
Her is what I have tried(sleep 2 ; echo user ; sleep 1; echo pass; sleep 2; echo netstat) | nc -t 10.10.10.34 23
gives this outputÿý%ÿûÿûÿý'ÿýÿýÿûWelcome to Microsoft Telnet Service
... (1 Reply)
Discussion started by: Jotne
1 Replies
10. Emergency UNIX and Linux Support
Dear Linux guru's
I am trying to create a webserver using nc (netcat only) on RHEL 7.2 running on bash shell.
now the easy thing is to get nc listing to a port and respond back
$ while true; do { echo -e 'HTTP/1.0 200 OK\r\n'; set; } | nc -l 7877; done
This when called from a... (3 Replies)
Discussion started by: chakrapani
3 Replies
LEARN ABOUT SUSE
aconnect
aconnect(1) General Commands Manual aconnect(1)
NAME
aconnect - ALSA sequencer connection manager
SYNOPSIS
aconnect [-d] [-options] sender receiver
aconnect -i|-o [-options]
aconnect -x
DESCRIPTION
aconnect is a utility to connect and disconnect two existing ports on ALSA sequencer system. The ports with the arbitrary subscription
permission, such as created by aseqview(1), can be connected to any (MIDI) device ports using aconnect. For example, to connect from port
64:0 to 65:0, run as follows:
% aconnect 64:0 65:0
The connection is one-way, and the whole data to the sender port (64:0) is redirected to the receiver port (65:0). When another port (e.g.
65:1) is attached to the same sender port, the data is sent to both receiver ports. For disconnection, use -d option.
% aconnect -d 64:0 65:0
The address can be given using the client's name.
% aconnect External:0 Emu8000:1
Then the port 0 of the client matching with the string "External" is connected to the port 1 of the client matching with the "Emu8000".
Another function of aconnect is to list the present ports on the given condition. The input ports, which may become sender ports, can be
listed with -i option.
% aconnect -i
client 0: 'System' [type=kernel]
0 'Timer '
1 'Announce '
client 64: 'External MIDI-0' [type=kernel]
0 'MIDI 0-0 '
Similarly, to see the output ports, use -o flag.
You can remove all existing exported connections using -x option. This function is useful for terminating the ALSA drivers, because the
modules with sequencer connections cannot be unloaded unless their connections are removed.
OPTIONS
CONNECTION MANAGEMENT
-d, --disconnect
Disconnect the given subscription.
-e, --exclusive
Connect ports with exclusive mode. Both sender and receiver ports can be no longer connected by any other ports.
-r, --real queue
Convert time-stamps of event packets to the current value of the given real-time queue. This is option is, however, not so useful,
since the receiver port must use (not necessarily own) the specified queue.
-t, --tick queue
Like -r option, but time-stamps are converted to the current value of the given tick queue.
LIST PORTS
-i, --input
List existing input (readable) ports. This option is exclusive to -o.
-o, --output
List existing output (writable) ports. This option is exclusive to -i.
-l, --list
List the current connection status. The connected and connecting ports from/to each port are listed together. The suffix flag [ex]
means the connection is exclusive. The suffix flag [real:#] and [tick:#] mean the connection includes real-time and tick conversion
on the listed queue, respectively.
REMOVE ALL CONNECTIONS
-x, --removeall
Remove all exported connections.
SEE ALSO
aseqnet(1), aseqview(1)
AUTHOR
Takashi Iwai <tiwai@suse.de>
August 31, 2000 aconnect(1)