I've been googling for a while now, trying to forward port 3000 to port 80....
In the past I used to DLink router to forward port 3000 to 80. I recently finished (well, is it ever done anyhow?) setting up my linux box and got it acting as a router.
I want to continue to run Apache on port 80... (1 Reply)
Hi,
I have to install an application that has a built in tftp server. Tftp comes in on port 69. As i am not installing this application as a root user i am running into trouble because only the root user can listen to ports < 1024. So changing the port i listen to to one greater than 1023 isn't... (1 Reply)
Hi
I want to set up port forwarding from one network to another network. I already have this configured on the Linux box using iptables.
iptables -t nat -A PREROUTING -p tcp -i eth1 --dport 1521 -j DNAT --to 10.218.146.230
iptables -A FORWARD -p tcp -i eth1 -d 10.218.146.230 -j ACCEPT
... (2 Replies)
Hi Linux/Unix Guru,
I am setting Linux Hopping Station to another different servers.
My current config to connect to another servers is using different port to connect.
e.g
ssh -D 1080 -p 22 username@server1.com
ssh -D 1081 -p 22 username@server2.com
Now what I would like to have... (3 Replies)
Hi,
can anyone please tell me how can i do port forwarding from unix box to windows box.
Which command will be used for this one.
thanks in advance.
Arpit (1 Reply)
Besides installing VNC on the red hat server which i know i can do, is there any RDP servers (using the windows rdp client) to remote control a red hat 6.2 server? Thanks in advance for this. (1 Reply)
Guys,
Can I use an open RDP port to gain ssh access to my Linux server running the other side of our firewall?
I work from home on the odd occasion, we only have RDP port 3389 available once logged into the VPN. I would rather ssh into my workstation without the need for a desktop display.
... (3 Replies)
hi guys
i have a simple question !
i have two ips . a valid and internal(172.16.11.2)
i want to use port forwarding to forward any request to valid IP port 8001 to internal ip port 80 .
i use this rule :
sysctl -w net.ipv4.ip_forward=1
iptables -t nat -A PREROUTING -p tcp... (1 Reply)
Hi experts,
We have windows machine ( A ) in one network & 2 Linux Servers ( B & C ) in another network. There is a firewall between these 2 networks and SSH (TCP/22) & HTTPS (TCP/443) are allowed from A to B only (but not to C). There is no personal firewall / iptables running on any machine.... (1 Reply)
Hello Gurus,
I have configured port forwarding at router.
But after configuration I am not able to connect the computer from outside/Over internet/Remote desktp from other computer.
Could you please advice?
Thanks-
Pokhraj (2 Replies)
Discussion started by: pokhraj_d
2 Replies
LEARN ABOUT FREEBSD
gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD