06-30-2014
The SEA is configured on the VIO server and without access to the VIO server, I don't think you have any way to see if there is one. I don't think the LPAR itself (not VIO server) would even know if it exists.
The LPAR's ethernet adapter is created on a VLAN matching what is on the VIO server's, but I don't know of any way to see the VLAN number from the LPAR. If you have access to the HMC, you can see it there.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
Discussion started by: sekarsamy
1 Replies
5. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
6. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
7. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
8. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT DEBIAN
roar_vs_vio_obj
roar_vs_connection_obj(3) RoarAudio Programmer's Manual roar_vs_connection_obj(3)
NAME
roar_vs_connection_obj, roar_vs_stream_obj, roar_vs_vio_obj - VS API interface for use of main API
SYNOPSIS
#include <roaraudio.h>
struct roar_connection * roar_vs_connection_obj(roar_vs_t * vss, int * error);
struct roar_stream * roar_vs_stream_obj (roar_vs_t * vss, int * error);
struct roar_vio_calls * roar_vs_vio_obj (roar_vs_t * vss, int * error);
DESCRIPTION
Those functions return internal connection, stream and VIO object of the VS object. They are used to use the main API with a VS opened
stream.
roar_vs_connection_obj() returns the connection object used for the control connection to the server.
roar_vs_stream_obj() returns the stream object storing information about the stream.
roar_vs_vio_obj() returns the VIO object used to read data from or send data to the server.
Returned objects are freed as soon as the VS object is closed. If the VS object was created using roar_vs_new_from_con(3) the connection is
not closed by the VS object and stay valid after close until it is closed by the program or library.
The VIO object MUST NOT be used while in buffered mode.
PARAMETERS
vss The VS object to return internal objects from.
error This is a pointer to a integer used to store the error value in case of error. This can be NULL if not used but it is very recom-
mended to use this error value to report good error messages to the user.
RETURN VALUE
On success these calls return the described object. On error, NULL is returned.
EXAMPLES
FIXME
SEE ALSO
roarvs(7), libroar(7), RoarAudio(7).
RoarAudio May 2011 roar_vs_connection_obj(3)