Sponsored Content
Operating Systems Linux Red Hat PC cannot reach two lan card Linux box Post 302907537 by solaris_user on Sunday 29th of June 2014 05:30:10 PM
Old 06-29-2014
Did you TCP wrappers ?

Do you have any entries in /etc/hosts.deny ?

And do you have router on your network or your Linux box is also a router ?

If Linux box is used as router you must enable ip forwarding in /etc/sysctl.conf and then load system parameters with syctl -p command.

Also I don't see anywhere information if you use SELinux.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Networking a SCO Unix box with a windows lan

Hi there! We have a SCO UNIX box that uses a bunch of dumb terminals. We also have a workgroup of 5 stations Is there a way that we can network the UNIX box to the workgroup for dumb terminal.. A novice would think you could TCP the UNIX machine through a hub and use hypertermal as a dumb... (6 Replies)
Discussion started by: huilai
6 Replies

2. UNIX for Advanced & Expert Users

LAN Card Problem !

The Lan card in one of our UIII WS's seem doesn't work,so with ping command i can not see any of the machines in LAN and with some other tests i'm sure it's not OK. I tried to use the second card on PCI port ,but the replaced card was one of the ordinary card for PC's ...by the way after... (1 Reply)
Discussion started by: nikk
1 Replies

3. Cybersecurity

lan card autonegotiation?

what is lan card autonegotiation ? how to enable and disable this feature? (2 Replies)
Discussion started by: nabil_boussetta
2 Replies

4. SCO

LAN card problem

Dear all Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working. Is... (1 Reply)
Discussion started by: ccvyas
1 Replies

5. Solaris

Does x86 solaris 9 support PCI RealTek Lan Card

Hi, i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card . Thank You, Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies

6. SCO

lan card not detecting

hi all i have installed SCO 5.0.5 on a "Netfinity 5000" IBM server. But the OS is not detecting the lan card. how can i detect it.... help and thanks in advance . bidhayak (3 Replies)
Discussion started by: bidhayakm
3 Replies

7. Programming

LAN card status Information

Please tell me API in Solaris / Linux / UNIX to get status information of LAN card. (1 Reply)
Discussion started by: mansoorulhaq
1 Replies

8. Linux

How to check the LAN card?

Hi. I have a lan card installed on my server. I want to check the duplex speed of it. How can I check it? Help is appreciated. Thank you. (3 Replies)
Discussion started by: Amol21
3 Replies

9. Solaris

Can't ping new PCI LAN card x4270_m2

Hi, I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10). I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies

10. Linux

Lan card not reaching Gateway

Hi, I have this problem on RHEL box. I am using two NIC's of same model and make (Intel 82557) in the adjacent PCI slots . I am using each one for different subnet and have assigned them ipaddresses and gateways of respective subnets . While one is O.K. connecting to its ... (5 Replies)
Discussion started by: dextergenious
5 Replies
FAITH(4)						   BSD Kernel Interfaces Manual 						  FAITH(4)

NAME
faith -- IPv6-to-IPv4 TCP relay capturing interface SYNOPSIS
device faith DESCRIPTION
The faith interface captures IPv6 TCP traffic, for implementing userland IPv6-to-IPv4 TCP relay like faithd(8). Each faith interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). Special action will be taken when IPv6 TCP traffic is seen on a router, and the routing table suggests to route it to the faith interface. In this case, the packet will be accepted by the router, regardless of the list of IPv6 interface addresses assigned to the router. The packet will be captured by an IPv6 TCP socket, if it has the IN6P_FAITH flag turned on and matching address/port pairs. As a result, faith will let you capture IPv6 TCP traffic to some specific destination addresses. Userland programs, such as faithd(8) can use this behavior to relay IPv6 TCP traffic to IPv4 TCP traffic. The program can accept some specific IPv6 TCP traffic, perform getsockname(2) to get the IPv6 destination address specified by the client, and perform application-specific address mapping to relay IPv6 TCP to IPv4 TCP. The IN6P_FAITH flag on a IPv6 TCP socket can be set by using setsockopt(2), with level IPPROTO_IPV6 and optname IPv6_FAITH. To handle error reports by ICMPv6, some ICMPv6 packets routed to an faith interface will be delivered to IPv6 TCP, as well. To understand how faith can be used, take a look at the source code of faithd(8). As the faith interface implements potentially dangerous operations, great care must be taken when configuring it. To avoid possible misuse, the sysctl(8) variable net.inet6.ip6.keepfaith must be set to 1 prior to using the interface. When net.inet6.ip6.keepfaith is 0, no packets will be captured by the faith interface. The faith interface is intended to be used on routers, not on hosts. SEE ALSO
inet(4), inet6(4), faithd(8) Jun-ichiro itojun Hagino and Kazu Yamamoto, An IPv6-to-IPv4 transport relay translator, RFC3142. HISTORY
The FAITH IPv6-to-IPv4 TCP relay translator first appeared in the WIDE hydrangea IPv6 stack. BSD
April 10, 1999 BSD
All times are GMT -4. The time now is 01:46 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy