Sponsored Content
Full Discussion: IPv6 question
Operating Systems Solaris IPv6 question Post 302907315 by jpolachak on Friday 27th of June 2014 09:44:59 AM
Old 06-27-2014
I have added /etc/defaultrouter6 and it does not do anything to get rid of my additional igb:2, igb:3 interfaces. However, this does not break anything. I am able still able to ping myself and the gateway. I am pinging the addresses via IP address.

---------- Post updated at 09:44 AM ---------- Previous update was at 08:22 AM ----------

I just realized this might help provide some more information. I am tyring to get this to work on a non global zone running solaris 10. My production server that "works" that I have been comparing against is a xen instance of Solaris 10 virutal machine running on a Oracle Linux server. Maybe my issue is something related to global and non global zones. At this time I do not have the global zone configured with IPv6 at all. I am going to configure it and report back.
 

8 More Discussions You Might Find Interesting

1. IP Networking

Solaris IPv6

Hi, Anybody who worked with IPv6 on Solaris 8. I want to get rid of IPv6 (Uninstall). Any comments ...ideas...will be highly appreciated. (4 Replies)
Discussion started by: s_aamir
4 Replies

2. IP Networking

IPv6 testbed

Hello guyz.. did some of u have implement or making a testbed for IPv6? if yes, can u attached the procedures and standard guidelines because i really need for my proposal.. thanx.. (2 Replies)
Discussion started by: unknown2205
2 Replies

3. Linux

ipv6 routing

I am trying to capture the ipv6 packets through pcap utility. For that i am redirecting the ipv6 packets to the loopback address , but the ipv6 packets are not getting redirected to tha loopback address.Instead they are taking there normal routes. (1 Reply)
Discussion started by: vikasmca05
1 Replies

4. Red Hat

IPv4 and IPv6 Related Question to CentOS VMs

Hello, I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch. I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies

5. HP-UX

Ipv6 on hpux

my problem: i want to change from ipv4 to ipv6 on my home network. On hpux i can assign only address non routable as fe80::1 fe80::3 etc to my lan0 Editing netconf-ipv6 i can assing a routable ipv6 address like fd55:282f:3b98::/48 or 2001:470:26:307:89a0:aba1:f98b:eb3e but only to alias... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies

6. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

7. IP Networking

IPv6 Problems

I am trying to setup an IPv6 network. I modified the interfaces file: /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback iface etho0 inet static address 2620:7:a000::1 netmask 64 gateway ::ffff:c0a8:101 ... (0 Replies)
Discussion started by: Meow613
0 Replies

8. Solaris

Solaris 10 IPv6

Hello Dears , please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface . Thanks in... (1 Reply)
Discussion started by: ttashman
1 Replies
net_zoneidtonetid(9F)					   Kernel Functions for Drivers 				     net_zoneidtonetid(9F)

NAME
net_zoneidtonetid - map a zoneid_t struture identifier to a netid_t structure SYNOPSIS
#include <sys/neti.h> netid_t net_zoneidtonetid(const zoneid_t zone); INTERFACE LEVEL
Solaris DDI specific (Solaris DDI). PARAMETERS
zone valid zoneid_t structure that refers to a running zone. DESCRIPTION
The net_zoneidtonetid() function maps the given zoneid_t structure (used to represent a zone that is currently running) into a netid_t structure that is associated with the IP instance supporting network functions for that zone. RETURN VALUES
The net_zoneidtonetid() function returns -1 if no mapping took place. Otherwise, it returns the netid_t structure currently used by the zoneid_t structure. For zones that are using a shared IP instance, the netid_t structure for the instance owned by the global zone is returned. CONTEXT
The net_zoneidtonetid() function may be called from user, kernel, or interrupt context. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ |Interface Stability |Committed | +-----------------------------+-----------------------------+ SEE ALSO
net_netidtozonid(9F), attributes(5) SunOS 5.11 1 May 2008 net_zoneidtonetid(9F)
All times are GMT -4. The time now is 09:22 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy