USB-Ethernet/Ethernet-USB Post: 302903631

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Ethernet

We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time...

2. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:...

3. AIX

ethernet down

Hello everyone I have a problem with one server, has Aix 5.3 in the errpt has this message IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN F3931284 ...

4. Solaris

Ethernet Port Name

I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ?

5. Solaris

ethernet

my solris box network is unreachable how to solve this ipaddress assiagning and entry in vi /etc/host how to solve network is unreachable

6. Solaris

solaris ethernet card and mounting usb drives

I had installed soalris 10 on my dell vostro 1400.It had installed succefully. If i type ifconfig -a it is showing only my loop back adpater. So how to tell me how to mount my usb drive and how to configure my lan ethernet card,My lan ethernet card is Broadcom. Tell me step...

7. UNIX for Dummies Questions & Answers

USB-USB cable between linux and windows computers

Is there an easy way to setup a cross-over cable (USB-USB) between a linux box and a windows PC? My 2 machines are next to each other but I really do not want to keep transfering my files using my USB drive. Thanks!

8. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter...

LEARN ABOUT FREEBSD

if_kue

KUE(4)							   BSD Kernel Interfaces Manual 						    KUE(4)

NAME

     kue -- Kawasaki LSI KL5KUSB101B USB Ethernet driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device uhci
	   device ohci
	   device usb
	   device kue

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_kue_load="YES"

DESCRIPTION

     The kue driver provides support for USB Ethernet adapters based on the Kawasaki LSI KL5KLUSB101B chipset.

     The KL5KLUSB101B supports a 128-entry multicast filter, single perfect filter entry for the station address and promiscuous mode.	Packets
     are received and transmitted over separate USB bulk transfer endpoints.

     The Kawasaki chipset supports only 10Mbps half-duplex mode, hence there are no ifmedia(4) modes to select.

     For more information on configuring this device, see ifconfig(8).

HARDWARE

     The kue driver supports Kawasaki LSI KL5KLUSB101B based USB Ethernet adapters including:

     o	 3Com 3c19250
     o	 3Com 3c460 HomeConnect Ethernet USB Adapter
     o	 ADS Technologies USB-10BT
     o	 AOX USB101
     o	 ATen UC10T
     o	 Abocom URE 450
     o	 Corega USB-T
     o	 D-Link DSB-650C
     o	 Entrega NET-USB-E45, NET-HUB-3U1E
     o	 I/O Data USB ETT
     o	 Kawasaki DU-H3E
     o	 LinkSys USB10T
     o	 Netgear EA101
     o	 Peracom USB Ethernet Adapter
     o	 Psion Gold Port USB Ethernet adapter
     o	 SMC 2102USB, 2104USB

DIAGNOSTICS

     kue%d: watchdog timeout  A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
     transmission before a timeout expired.

     kue%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

SEE ALSO

     arp(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The kue device driver first appeared in FreeBSD 4.0.

AUTHORS

     The kue driver was written by Bill Paul <wpaul@ee.columbia.edu>.

BUGS

     The kue driver does not accumulate Ethernet collisions statistics because the Kawasaki firmware does not appear to maintain any internal sta-
     tistics.

BSD
								  October 7, 2006							       BSD