As for your other question, the server is used as a media storage and backup for 5-10 users during the day. Anything that needs downtime can be done in the weekend.
I hope that answers your question, and many thanks for your help again.
Hi,
Since last week our server become too slow when we try to run application on it. When we run top command, it show as below:
So it's nothing to do with heavy utilization, right? Can you give some opinion on what actually had happended?
Thank you very much... :b: (4 Replies)
I have data file with customer.dat, and this contains the customer names
>cat customer.dat
FirstName1 LastName1
FistName2 LastName1
FistName3 MiddleName3 LastName3
This file can contain areoun 100 customer names.
Regards, (1 Reply)
Hi,
I have an excel file that have a random count of columns/fields and what im trying to do is to only retrieve all the rows under 2 specific field headers.
I can use the usually command for awk which is awk 'print{ $1 $2}' > output.txt, but the location of the 2 specific field headers is... (9 Replies)
Hello,
I am using Redhat redhat 4 update 4 kernal 2.6. My server is some time suddenly running slow.
The averge cpu load goes up to 50 to 60. (There is only two CPU and usually, the averge load
is between 1 to 2.5) That time, i see, there are several sessions connected.
Normally, we have... (5 Replies)
I need to find all the files that have group Read or Write permission or files that have user write permission.
This is what I have so far:
find . -exec ls -l {} \; | awk '/-...rw..w./ {print $1 " " $3 " " $4 " " $9}'
It shows me all files where group read = true, group write = true... (5 Replies)
Hi,
We have smb client running on two of the linux boxes and smb server on another linux system. During a backup operation which uses smb, read of a file was allowed while write to the same file was going on.Also simultaneous writes to the same file were allowed.Following are the settings in the... (1 Reply)
Dear All,
I have a hard disk in solaris on which the write performanc is too slow.
The CPU , RAM memory are absolutely fine.
What might be reason.
Kindly explain.
Rj (9 Replies)
There is a big problem with the server (VPS based on OpenVZ, CentOS 5, 3GB RAM). The problem is the following. The first 15-20 minutes after starting the server is operating normally, the load average is less than or about 1.0, but then begins to increase sharply% wa, then hovers around 95-99%.... (2 Replies)
Discussion started by: draiphod
2 Replies
LEARN ABOUT DEBIAN
bup-server
bup-server(1) General Commands Manual bup-server(1)NAME
bup-server - the server side of the bup client-server relationship
SYNOPSIS
bup server
DESCRIPTION
bup server is the server side of a remote bup session. If you use bup-split(1) or bup-save(1) with the -r option, they will ssh to the
remote server and run bup server to receive the transmitted objects.
There is normally no reason to run bup server yourself.
MODES
smart In this mode, the server checks each incoming object against the idx files in its repository. If any object already exists, it
tells the client about the idx file it was found in, allowing the client to download that idx and avoid sending duplicate data.
This is bup-server's default mode.
dumb In this mode, the server will not check its local index before writing an object. To avoid writing duplicate objects, the server
will tell the client to download all of its .idx files at the start of the session. This mode is useful on low powered server hard-
ware (ie router/slow NAS).
FILES
$BUP_DIR/bup-dumb-server
Activate dumb server mode, as discussed above. This file is not created by default in new repositories.
SEE ALSO bup-save(1), bup-split(1)BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown-bup-server(1)