Hi,
Since last week our server become too slow when we try to run application on it. When we run top command, it show as below:
So it's nothing to do with heavy utilization, right? Can you give some opinion on what actually had happended?
Thank you very much... :b: (4 Replies)
I have data file with customer.dat, and this contains the customer names
>cat customer.dat
FirstName1 LastName1
FistName2 LastName1
FistName3 MiddleName3 LastName3
This file can contain areoun 100 customer names.
Regards, (1 Reply)
Hi,
I have an excel file that have a random count of columns/fields and what im trying to do is to only retrieve all the rows under 2 specific field headers.
I can use the usually command for awk which is awk 'print{ $1 $2}' > output.txt, but the location of the 2 specific field headers is... (9 Replies)
Hello,
I am using Redhat redhat 4 update 4 kernal 2.6. My server is some time suddenly running slow.
The averge cpu load goes up to 50 to 60. (There is only two CPU and usually, the averge load
is between 1 to 2.5) That time, i see, there are several sessions connected.
Normally, we have... (5 Replies)
I need to find all the files that have group Read or Write permission or files that have user write permission.
This is what I have so far:
find . -exec ls -l {} \; | awk '/-...rw..w./ {print $1 " " $3 " " $4 " " $9}'
It shows me all files where group read = true, group write = true... (5 Replies)
Hi,
We have smb client running on two of the linux boxes and smb server on another linux system. During a backup operation which uses smb, read of a file was allowed while write to the same file was going on.Also simultaneous writes to the same file were allowed.Following are the settings in the... (1 Reply)
Dear All,
I have a hard disk in solaris on which the write performanc is too slow.
The CPU , RAM memory are absolutely fine.
What might be reason.
Kindly explain.
Rj (9 Replies)
There is a big problem with the server (VPS based on OpenVZ, CentOS 5, 3GB RAM). The problem is the following. The first 15-20 minutes after starting the server is operating normally, the load average is less than or about 1.0, but then begins to increase sharply% wa, then hovers around 95-99%.... (2 Replies)
Discussion started by: draiphod
2 Replies
LEARN ABOUT BSD
iostat
IOSTAT(1) General Commands Manual IOSTAT(1)NAME
iostat - report I/O statistics
SYNOPSIS
iostat [ drives ] [ interval [ count ] ]
DESCRIPTION
Iostat iteratively reports the number of characters read and written to terminals per second, and, for each disk, the number of transfers
per second, kilobytes transferred per second, and the milliseconds per average seek. It also gives the percentage of time the system has
spent in user mode, in user mode running low priority (niced) processes, in system mode, and idling.
To compute this information, for each disk, seeks and data transfer completions and number of words transferred are counted; for terminals
collectively, the number of input and output characters are counted. Also, each sixtieth of a second, the state of each disk is examined
and a tally is made if the disk is active. From these numbers and given the transfer rates of the devices it is possible to determine
average seek times for each device.
The optional interval argument causes iostat to report once each interval seconds. The first report is for all time since a reboot and
each subsequent report is for the last interval only.
The optional count argument restricts the number of reports.
If more than 4 disk drives are configured in the system, iostat displays only the first 4 drives, with priority given to Massbus disk
drives (i.e. if both Unibus and Massbus drives are present and the total number of drives exceeds 4, then some number of Unibus drives will
not be displayed in favor of the Massbus drives). To force iostat to display specific drives, their names may be supplied on the command
line.
FILES
/dev/kmem
/vmunix
SEE ALSO vmstat(1)4th Berkeley Distribution April 29, 1985 IOSTAT(1)