05-14-2014
Ethernet devices are not found in /dev, they do not have corresponding device files.
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
i purchased, what was labeled as a 4-port fast ethernet sbus card from ebay.
i installed it in my ultra1, and it seems to be working fine. how can i determine if the card is infact a fast ethernet card vs. the standard ethernet 4-port card? (7 Replies)
Discussion started by: xyyz
7 Replies
2. UNIX for Dummies Questions & Answers
hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
Discussion started by: tyskertøs
6 Replies
3. Solaris
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
Discussion started by: kurva
1 Replies
4. Solaris
I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
Discussion started by: StarSol
4 Replies
5. Linux
Sir,
Do linux have device file for ethernet card. Can I use open , read , write , system calls to read data transferred through LAN. Is there any methods to read network datas (with out header and tailor information).
Hope anyone can help me out. Thanking you....
... (5 Replies)
Discussion started by: iamjayanth
5 Replies
6. Red Hat
I have a RAC setup that was configured before I started at my new company. I would like to reconfigure the network devices and change the names. How complex is this regarding the Oracle RAC environment? Does the Oracle RAC rely on the device name or is it only relying on the IP information?
... (1 Reply)
Discussion started by: s ladd
1 Replies
7. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
8. UNIX for Advanced & Expert Users
Currently I am using this laborious command
lvdisplay | awk '/LV Path/ {p=$3} /LV Name/ {n=$3} /VG Name/ {v=$3} /Block device/ {d=$3; sub(".*:", "/dev/dm-", d); printf "%s\t%s\t%s\n", p, "/dev/mapper/"v"-"n, d}'
Would like to know if there is any shorter method to get this mapping of... (2 Replies)
Discussion started by: royalibrahim
2 Replies
LEARN ABOUT DEBIAN
bpqparms
BPQPARMS(8) Linux System Managers Manual BPQPARMS(8)
NAME
bpqparms - Configure BPQ ethernet devices.
SYNOPSIS
bpqparms device [-a ethaddr] [-d ethaddr] [-vV]
DESCRIPTION
Bpqparms allows the setting of the BPQ Ethernet options for a particular device. Each BPQ Ethernet device appears as a device named
bpq0...bpqN which overlays the original Ethernet device, usually eth0...ethN. This device is an AX.25 device driver and allows AX.25 frames
to be transmitted over an Ethernet to another machine using the same protocol. The default for the device is to send and receive BPQ Ether-
net packets to the broadcast address. This program replaces the previous "axparms -dev" option.
OPTIONS
-a ethaddr Allows the setting of which ethernet address will be accepted by the BPQ Ethernet device.
-d ethaddr If specified on its own, will set the destination ethernet address will be used for transmitting and for receiving of BPQ
ethernet packets. An address of "broadcast" sets it to the ethernet broadcast address.
-v Displays the version number.
-V The original version messages.
SEE ALSO
ax25(4), axports(5), ifconfig(8).
AUTHOR
Joerg Reuter DL1BKE <jreuter@poboxes.com>
Linux 4 September 1996 BPQPARMS(8)