Hi,
How to write a script to perform telnet/ftp operation.
Also please refer some site to get reference about shell scripting.
Thanks in advance
-Arun. (1 Reply)
I am trying to use telnet in shell script but getting following error
error
Connected to crmapp00.agf.ca.
Escape character is '^]'.
Connection closed by foreign host.
Script
#!/bin/ksh
PATH=/usr/sbin/:/usr/bin:/usr/ucb:/etc:/usr/local/bin:.
telnet HOSTNAME <<SCRIPT
user userid... (9 Replies)
Hi All,
I was trying to use telnet in a script to access a certain processor on a certain port to view some processes. The problem is that when I use telnet the output is displayed for me.
The script is:
#!/bin/sh
cd /ahmed/ezzat/
rm ss7trace.log
touch ss7trace.log
chmod 755... (3 Replies)
Hi Guys,
How do I write the script for the following
telnet 192.168.1.100 9002
if the result is less than 1 second. The script should say as port open
if the result takes more than 3 seconds. The script should display as port closed.
Thanks,
Charan (1 Reply)
Hi all,
I would like to write a ad hoc shell script that would allow me to do some telnet tests to multiple IP's and ports at the same time . So, I want to determine which one is successful and which one fails. So, basically I would like the shell to spawn the telnet test and to break out of... (3 Replies)
Hi,
I need a script that take one parameter as destination hostname and two parameter as ranges and tries telnet and records the successful connections.
fo reg:
./testtelnet.sh destination-host 1000 1050
should give me all the port between 1000 and 1050 what successfully connected to... (10 Replies)
Hello,
I wrote a script for doing telnet.However the requirement got changed and now I have to write a telnet script that will
1. Do the telnet from all the virtual ips in a box(Ex: x.x.x.x is the box ip, and x.x.x.1,x.x.x.2 etc are virtual ips associated with that box.)
2. The port range... (0 Replies)
Hello,
I wrote a script for doing telnet.However the requirement got changed and now I have to write a telnet script that will
1. Do the telnet from all the virtual ips in a box(Ex: x.x.x.x is the box ip, and x.x.x.1,x.x.x.2 etc are virtual ips associated with that box.)
2. The port range... (3 Replies)
Discussion started by: coolkid
3 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)