Assuming that PWR0 means the power is off and PWR1 means the power is on, and assuming that you want to mute if the power is on, I think you want something more like:
Obviously, this is untested (since I don't have an amp like this). If the amplifier has a command to terminate a command session, (something like exit or quit) you probably also want to add an echo to send that command to the amplifier in both of the above telnet scripts after the 2nd sleep.
Last edited by Don Cragun; 05-10-2014 at 08:44 PM..
Reason: Add missing quotes.
Hi,
How to write a script to perform telnet/ftp operation.
Also please refer some site to get reference about shell scripting.
Thanks in advance
-Arun. (1 Reply)
I am trying to use telnet in shell script but getting following error
error
Connected to crmapp00.agf.ca.
Escape character is '^]'.
Connection closed by foreign host.
Script
#!/bin/ksh
PATH=/usr/sbin/:/usr/bin:/usr/ucb:/etc:/usr/local/bin:.
telnet HOSTNAME <<SCRIPT
user userid... (9 Replies)
Hi All,
I was trying to use telnet in a script to access a certain processor on a certain port to view some processes. The problem is that when I use telnet the output is displayed for me.
The script is:
#!/bin/sh
cd /ahmed/ezzat/
rm ss7trace.log
touch ss7trace.log
chmod 755... (3 Replies)
Hi Guys,
How do I write the script for the following
telnet 192.168.1.100 9002
if the result is less than 1 second. The script should say as port open
if the result takes more than 3 seconds. The script should display as port closed.
Thanks,
Charan (1 Reply)
Hi all,
I would like to write a ad hoc shell script that would allow me to do some telnet tests to multiple IP's and ports at the same time . So, I want to determine which one is successful and which one fails. So, basically I would like the shell to spawn the telnet test and to break out of... (3 Replies)
Hi,
I need a script that take one parameter as destination hostname and two parameter as ranges and tries telnet and records the successful connections.
fo reg:
./testtelnet.sh destination-host 1000 1050
should give me all the port between 1000 and 1050 what successfully connected to... (10 Replies)
Hello,
I wrote a script for doing telnet.However the requirement got changed and now I have to write a telnet script that will
1. Do the telnet from all the virtual ips in a box(Ex: x.x.x.x is the box ip, and x.x.x.1,x.x.x.2 etc are virtual ips associated with that box.)
2. The port range... (0 Replies)
Hello,
I wrote a script for doing telnet.However the requirement got changed and now I have to write a telnet script that will
1. Do the telnet from all the virtual ips in a box(Ex: x.x.x.x is the box ip, and x.x.x.1,x.x.x.2 etc are virtual ips associated with that box.)
2. The port range... (3 Replies)
Discussion started by: coolkid
3 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)