sco unix 5.0.x, several weeks ago, I add a telnet-like service in inetd.conf, it runs well for 100 network terminals.
But nowdays, the terminals can connect to server successfully after booting machine, but several hours later, can not connect. "netstat -p tcp -a" can NOT find the port in... (1 Reply)
Discussion started by: shark_gao
1 Replies
2. Post Here to Contact Site Administrators and Moderators
Dear Administrators,
I think Mr. Vino is one of your Moderators here because he closes this thread: https://www.unix.com/showthread.php?p=302086230#post302086230
without a valid reason.
Rule 7 states no headhunters or recruiters, but career advice is not prohibited here i think, because it... (2 Replies)
Hi folks,
First of all, sorry about my english, isn't the best and thks for advance.
Here es my problem...
I have virtualize an SCO unix with VMware ESX 3 and everything was going on beatifull until that i try to connect from anorther host, i can't do it so i check the connection with... (5 Replies)
Hello,
Actually there are some bugs in application which does not close the TCP connection to other server though CORBA.
We need to kill that ESTABLISHED connections as new connection are not happeneing as the allocated ports were used and showing as ESTABLISHED
Is there any... (4 Replies)
Dear experts,
I am seeing a lot of TCP failed connection attempts from "netstat -s" on one of our servers.
How can I pin point what connection failed and what are the ports involved?
Any tools/commands I can dig in deeper to diag. what went wrong on these "failed connection attempts"?
... (2 Replies)
I've recently installed Solaris 10 10/9 in a new Dell Power Edge 630. Whenever I try to telnet, ssh, or FTP TO this box FROM another box on the same network segment, the following occurs:
Roughly 80% of the time I get "Unable to connect to remote host: Connection refused"
The remaining 20%... (0 Replies)
I have a TCPIP server application (a Vendor package) which by default allows 10 connections. It provides a parameter to allow us to increase the maximum allowable connections in case it is needed. Intermittently this application is failing with maximum number of connections reached even when there... (1 Reply)
Discussion started by: AIX_user
1 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)