Hi,
I am trying to use awk to split line before the pattern:
abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890
I need it to be like this:
abcde 12345 67890
abcde 12345 67890
abcde 12345 67890
abcde... (7 Replies)
Hi,
I want to split before reading the complete line as the line is very big and its throwing out of memory. can you suggest.
when i say
#cat $inputFile | while read eachLine
and use the eachLine to split its throwing out of memory as the line size is more than 10000000 characters.
Can you... (1 Reply)
Dear All,
I want to split single line into two line or three lines wherever “|” separated values comes using
Input line
test,DEMTEMPUT20100404010012,,,,,,,,|0070086|0070087,
output shoule be
test,DEMTEMPUT20100404010012,,,,,,,,0070086,
test,DEMTEMPUT20100404010012,,,,,,,,0070087, (14 Replies)
I guess this has a simple solution but can't figure out now.
having:
x="H:a:b:c"
to get H:
echo $x|awk -F: {'print $1'}
how can I put REST of line in another one? i.e.
echo $rest
a:b:c
thanks
---------- Post updated at 08:58 PM ---------- Previous update was at... (5 Replies)
Hi,
I have a file that contains multiple lines e.g.
/Plane/Wing/Engine/Rotorblades
I cannot use print $4 as the directories will be different lengths.
All i would like to do is print the very last column in each line in the file i.e. in this case, Rotorblades.
The code i... (4 Replies)
Hi All,
I'm trying to figure out which are the trusted-ips and which are not using a script file.. I have a file named 'ip-list.txt' which contains some ip addresses and another file named 'trusted-ip-list.txt' which also contains some ip addresses. I want to read a line from... (4 Replies)
Hi All,
Hope you guys had a wonderful weekend
I have a scenario where in which I have to read a file line by line
and check for few words before redirecting to a file
I have searched the forum but,either those answers dint work (perhaps because of my wrong under standing of how IFS... (6 Replies)
Hi All
Is there a way to export every line into new txt file where by the title of each txt output are same as the line ?
I have this txt files containing names:
Kandra Vanhooser
Rhona Menefee
Reynaldo Hutt
Houston Rafferty
Charmaine Lord
Albertine Poucher
Juana Maes
Mitch Lobel... (2 Replies)
I have a very long line in a file separated by "|" delimiter like below. Due to the length of the line, I find it very difficult to read to find a match line.
file = temp.txt
word 1| word 2 | word 3|....
I would like to read the file temp.txt and print out all words line by line like... (1 Reply)
TEXT2PS(L) TEXT2PS(L)
NAME
text2ps - convert text files to PostScript
SYNOPSIS
text2ps [ options ] [ files ]
DESCRIPTION
Text2ps reads the input files (standard input if none are specified) and produces PostScript code which, when fed to a PostScript printer,
will print the files. With text2ps it is possible to select any font, point size and number of columns. Options and files can be inter-
mixed on the command line. Options are effective for all following files until they are overridden.
Options
Here follows a list of options that text2ps recognizes. Most numeric arguments are significant to one decimal place. Options are evalu-
ated from left to right. Later options override earlier ones.
-# n Print n copies of each page. (Default 1.)
-c n Print in n columns. (Default 1.)
-f font
Print using font font. (Default Courier.)
-p n Print with point size n. (Default 9.)
-v n Use a vertical spacing of n points. If the vertical spacing is set to 0, the spacing will be 1.2 times the point size. (Default
0.)
-l n Print n lines per column. When the line count is 0, print as many lines as will fit. (Default 0.)
-r [p|l]
Set the orientation to either portrait mode (p) or landscape mode (l). (Default p.)
-b [+|-]
Set page break mode. An argument + will force new files to be always printed on a new page (this is the default). After - new
files will be put on the same page if there are still empty columns and the number of columns, the orientation or the number of
copies didn't change. New files always start new columns. (Default -.)
-mt n The top margin is n points. (Default 63.)
-mb n The bottom margin is n points. (Default 63.)
-ml n The left margin is n points. (Default 59.)
-mr n The right margin is n points. (Default 59.)
-mg n The inter-column gap is n points. (Default 25.)
-t [+|-]
If the argument is + the name of the file being printed will be printed on each page. If the argument is - the file name will not
be printed. -t + implies -b +.
-T text
Print text as title on each page. This implies -t - and -b +. This option can be switched off by specifying -t - or -t +.
(Default no title.)
-F font
Set the title font to font. (Default Helvetica.)
-P n Set the title point size to n. (Default 12.)
-B n Draw borders around each page. The number n specifies how to draw borders. N can have any of the following values or-ed in:
1 Draw a line along the left of the page.
2 Draw a line along the bottom of the page.
4 Draw a line along the right of the page.
8 Draw a line along the top of the page.
16 Draw a line between columns. This line does not connect to the lines along the top or bottom.
32 Draw a connecting line between the line between columns and the line along the top.
64 Draw a connecting line between the line between columns and the line along the bottom.
When n is 0, no border lines are drawn. (Default no bordering lines.)
-w n Tab stops are set every n spaces. Set the width of the TAB character. (Default 8.)
-1 Sets up options to print in one column in portrait mode with the Courier font, so that you get 66 lines on a page. Equivalent to
specifying the options -c 1 -f Courier -p 9 -v 0 -r p -l 0 -mt 63 -mb 63 -ml 59 -mr 59.
This is the default.
-2 Sets up options to print in two columns in landscape mode with the Courier font, so that you get two 66-line columns on a page.
Equivalent to specifying the options -c 2 -f Courier -p 6 -v 0 -r l -l 0 -mt 63 -mb 63 -ml 59 -mr 59 -mg 25. Together with the -1
option, this is probably the most useful option.
The name - means standard input.
BUGS
Too many options.
There is no way to specify where the title will be placed.
If the font being used is not a constant width font and there are other characters than just tabs and spaces in front of a tab, the next
character may not align properly.
TEXT2PS(L)