Hi,
I am trying to use awk to split line before the pattern:
abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890
I need it to be like this:
abcde 12345 67890
abcde 12345 67890
abcde 12345 67890
abcde... (7 Replies)
Hi,
I want to split before reading the complete line as the line is very big and its throwing out of memory. can you suggest.
when i say
#cat $inputFile | while read eachLine
and use the eachLine to split its throwing out of memory as the line size is more than 10000000 characters.
Can you... (1 Reply)
Dear All,
I want to split single line into two line or three lines wherever “|” separated values comes using
Input line
test,DEMTEMPUT20100404010012,,,,,,,,|0070086|0070087,
output shoule be
test,DEMTEMPUT20100404010012,,,,,,,,0070086,
test,DEMTEMPUT20100404010012,,,,,,,,0070087, (14 Replies)
I guess this has a simple solution but can't figure out now.
having:
x="H:a:b:c"
to get H:
echo $x|awk -F: {'print $1'}
how can I put REST of line in another one? i.e.
echo $rest
a:b:c
thanks
---------- Post updated at 08:58 PM ---------- Previous update was at... (5 Replies)
Hi,
I have a file that contains multiple lines e.g.
/Plane/Wing/Engine/Rotorblades
I cannot use print $4 as the directories will be different lengths.
All i would like to do is print the very last column in each line in the file i.e. in this case, Rotorblades.
The code i... (4 Replies)
Hi All,
I'm trying to figure out which are the trusted-ips and which are not using a script file.. I have a file named 'ip-list.txt' which contains some ip addresses and another file named 'trusted-ip-list.txt' which also contains some ip addresses. I want to read a line from... (4 Replies)
Hi All,
Hope you guys had a wonderful weekend
I have a scenario where in which I have to read a file line by line
and check for few words before redirecting to a file
I have searched the forum but,either those answers dint work (perhaps because of my wrong under standing of how IFS... (6 Replies)
Hi All
Is there a way to export every line into new txt file where by the title of each txt output are same as the line ?
I have this txt files containing names:
Kandra Vanhooser
Rhona Menefee
Reynaldo Hutt
Houston Rafferty
Charmaine Lord
Albertine Poucher
Juana Maes
Mitch Lobel... (2 Replies)
I have a very long line in a file separated by "|" delimiter like below. Due to the length of the line, I find it very difficult to read to find a match line.
file = temp.txt
word 1| word 2 | word 3|....
I would like to read the file temp.txt and print out all words line by line like... (1 Reply)
Vend::Payment::iTransact(3pm) User Contributed Perl Documentation Vend::Payment::iTransact(3pm)NAME
Vend::Payment::iTransact - Interchange iTransact Support
SYNOPSIS
&charge=itransact
or
[charge mode=itransact param1=value1 param2=value2]
PREREQUISITES
Net::SSLeay
or
LWP::UserAgent and Crypt::SSLeay
Only one of these need be present and working.
DESCRIPTION
The Vend::Payment::iTransact module implements the itransact() routine for use with Interchange. It is compatible on a call level with the
other Interchange payment modules.
To enable this module, place this directive in "interchange.cfg":
Require module Vend::Payment::iTransact
This must be in interchange.cfg or a file included from it.
Make sure CreditCardAuto is off (default in Interchange demos).
The mode can be named anything, but the "gateway" parameter must be set to "itransact". To make it the default payment gateway for all
credit card transactions in a specific catalog, you can set in "catalog.cfg":
Variable MV_PAYMENT_MODE itransact
It uses several of the standard settings from Interchange payment. Any time we speak of a setting, it is obtained either first from the
tag/call options, then from an Interchange order Route named for the mode, then finally a default global payment variable, For example, the
"id" parameter would be specified by:
[charge mode=itransact id=YouriTransact]
or
Route itransact id YouriTransactID
or
Variable MV_PAYMENT_ID YouriTransactID
The active settings are:
id Your iTransact account ID, supplied by iTransact when you sign up. Global parameter is MV_PAYMENT_ID.
home_page
The internet address of your site. Defaults to "http://__SERVER_NAME__" if not set. Global parameter is MV_PAYMENT_HOME_PAGE.
remap
This remaps the form variable names to the ones needed by iTransact. See the "Payment Settings" heading in the Interchange
documentation for use.
Troubleshooting
Try the instructions above, then enable test mode. A test order should complete.
Then move to live mode and try a sale with the card number "4111 1111 1111 1111" and a valid expiration date. The sale should be denied,
and the reason should be in [data session payment_error].
If nothing works:
o Make sure you "Require"d the module in interchange.cfg:
Require module Vend::Payment::iTransact
o Make sure either Net::SSLeay or Crypt::SSLeay and LWP::UserAgent are installed and working. You can test to see whether your Perl
thinks they are:
perl -MNet::SSLeay -e 'print "It works
"'
or
perl -MLWP::UserAgent -MCrypt::SSLeay -e 'print "It works
"'
If either one prints "It works." and returns to the prompt you should be OK (presuming they are in working order otherwise).
o Check the error logs, both catalog and global.
o Make sure you set your account ID properly.
o Try an order, then put this code in a page:
<XMP>
[calc]
my $string = $Tag->uneval( { ref => $Session->{payment_result} });
$string =~ s/{/{
/;
$string =~ s/,/,
/g;
return $string;
[/calc]
</XMP>
That should show what happened.
o If all else fails, consultants are available to help with integration for a fee. See http://www.icdevgroup.org/
BUGS
There is actually nothing *in* Vend::Payment::iTransact. It changes packages to Vend::Payment and places things there.
AUTHORS
Mark Johnson and Cameron Prince, based on original code by Mike Heins.
perl v5.14.2 2011-03-09 Vend::Payment::iTransact(3pm)