Hi,
I am trying to use awk to split line before the pattern:
abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890 abcde 12345 67890
I need it to be like this:
abcde 12345 67890
abcde 12345 67890
abcde 12345 67890
abcde... (7 Replies)
Hi,
I want to split before reading the complete line as the line is very big and its throwing out of memory. can you suggest.
when i say
#cat $inputFile | while read eachLine
and use the eachLine to split its throwing out of memory as the line size is more than 10000000 characters.
Can you... (1 Reply)
Dear All,
I want to split single line into two line or three lines wherever “|” separated values comes using
Input line
test,DEMTEMPUT20100404010012,,,,,,,,|0070086|0070087,
output shoule be
test,DEMTEMPUT20100404010012,,,,,,,,0070086,
test,DEMTEMPUT20100404010012,,,,,,,,0070087, (14 Replies)
I guess this has a simple solution but can't figure out now.
having:
x="H:a:b:c"
to get H:
echo $x|awk -F: {'print $1'}
how can I put REST of line in another one? i.e.
echo $rest
a:b:c
thanks
---------- Post updated at 08:58 PM ---------- Previous update was at... (5 Replies)
Hi,
I have a file that contains multiple lines e.g.
/Plane/Wing/Engine/Rotorblades
I cannot use print $4 as the directories will be different lengths.
All i would like to do is print the very last column in each line in the file i.e. in this case, Rotorblades.
The code i... (4 Replies)
Hi All,
I'm trying to figure out which are the trusted-ips and which are not using a script file.. I have a file named 'ip-list.txt' which contains some ip addresses and another file named 'trusted-ip-list.txt' which also contains some ip addresses. I want to read a line from... (4 Replies)
Hi All,
Hope you guys had a wonderful weekend
I have a scenario where in which I have to read a file line by line
and check for few words before redirecting to a file
I have searched the forum but,either those answers dint work (perhaps because of my wrong under standing of how IFS... (6 Replies)
Hi All
Is there a way to export every line into new txt file where by the title of each txt output are same as the line ?
I have this txt files containing names:
Kandra Vanhooser
Rhona Menefee
Reynaldo Hutt
Houston Rafferty
Charmaine Lord
Albertine Poucher
Juana Maes
Mitch Lobel... (2 Replies)
I have a very long line in a file separated by "|" delimiter like below. Due to the length of the line, I find it very difficult to read to find a match line.
file = temp.txt
word 1| word 2 | word 3|....
I would like to read the file temp.txt and print out all words line by line like... (1 Reply)
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)