03-14-2014
Solaris Cluster Failover based on scan rate
Dear Experts,
If there is a possible Solaris Cluster failover to second node based on scan rate?
I need the documentation If solaris cluster can do this.
Thank You in Advance
Edy
10 More Discussions You Might Find Interesting
1. High Performance Computing
I have rcently setup a 4 node cluster running sun cluster 3.2
and I have installed 4 zones on each node. when installing the zones I had to install the zone on all nodes the on the last node do a zlogin -C <zonename>
this worked ok.
theni I tried to siwitch the zone to node a thei work... (14 Replies)
Discussion started by: lesliek
14 Replies
2. HP-UX
I have a 2-node ServiceGuard cluster. One of the cluster packages has a volume group assigned to it. When I fail the package over to the other node, the volume group does not come up automatically on the other node.
I have to manually do a "vgchange -a y vgname" on the node before the package... (5 Replies)
Discussion started by: Wotan31
5 Replies
3. Solaris
Hi,
We have two sun SPARC server in Clustered (Sun Cluster 3.1). For some reason, System 1 failed over to System 2. Where can I find the logs which could tell me the reason for this failover?
Thanks (5 Replies)
Discussion started by: Mack1982
5 Replies
4. Gentoo
How to failover the cluster ? GNU/Linux
By which command,
My Linux version
2008 x86_64 x86_64 x86_64 GNU/Linux
What are the prerequisites we need to take while failover ?
if any
Regards (3 Replies)
Discussion started by: sidharthmellam
3 Replies
5. AIX
Hello,
How can i tell ifthe ratio between fr and sr is ok?
is fr/sr ratio of 0.9 acceptable?
thanks. (1 Reply)
Discussion started by: LiorAmitai
1 Replies
6. AIX
Hi Guys,
The management is being frisky about scan rate in the range of a few thousands ( 4 digit scan rates occasionally). After much research ive concluded that its ok to have high scan rates , unless it leads to swapping/ it falls above 1:4 ratio with free rate (fr:sr)
My question is:... (2 Replies)
Discussion started by: muzahed
2 Replies
7. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
8. Solaris
Hi All,
I need suggestions to monitoring Scan Rate on Solaris Operating System.
Any idea?
Thanks
Edy (5 Replies)
Discussion started by: edydsuranta
5 Replies
9. Solaris
Hi There,
Just curious here...
If there formula to calculate scan rate on solaris?
Thanks
Edy (3 Replies)
Discussion started by: edydsuranta
3 Replies
10. Red Hat
Hi Guys,
I am not much aware of clusters but i have few questions can someone provide the overview as it would be very helpful for me.
How can i perform cluster failover test to see all the services are failing back to other node ? If it is using veritas cluster then what kind of... (2 Replies)
Discussion started by: munna529
2 Replies
LEARN ABOUT OPENSOLARIS
scconf_transp_adap_qfe
scconf_transp_adap_qfe(1M) System Administration Commands scconf_transp_adap_qfe(1M)
NAME
scconf_transp_adap_qfe - configure the qfe transport adapter
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
You can configure qfe Ethernet adapters as cluster transport adapters. These adapters can only be used with transport type dlpi.
The qfe Ethernet adapter connects to a transport switch or to another Ethernet adapter on a different node. In either case, the connection
is made through a transport cable.
When a transport switch is used and the endpoints of the transport cable are configured by using scconf, scinstall, or other tools, you are
asked to specify a port name on the transport switch. You can provide any port name, or accept the default, as long as the name is unique
for the switch.
The default is to set the port name to the node ID hosting the adapter at the other end of the cable.
There are no user configurable properties for cluster transport adapters of this type.
SEE ALSO
Intro(1CL), clinterconnect(1CL), clnode(1CL), scconf(1M), scinstall(1M), qfe(7d)
Sun Cluster 3.2 4 May 2006 scconf_transp_adap_qfe(1M)