Hi,
We have AIX 5.1 machine of RAM 8 GB and paging space is 8GB. we are getting high memory usage of almost 99%.Can anybody please help in this ?
Partial vmstat o/p
kthr memory
----- -----------
r b avm fre
2 1 278727 1143
There is no paging issue.Becoz in... (5 Replies)
Hello.
I have a slackware system running cups with an HP laserJet 2100 connected via parallel port in ECP mode. Print jobs are working. Very slowly.
15K test print out of cups takes about 2 minutes to complete.
When the printout is on the way to the printer, the process "parallel" uses... (0 Replies)
Hi,
monitor memory usage on AIX machine on any day of the week from 3:00 PM ET to 5:00 PM ET -
Povide min and max memory consumption.
Determine if all of the available memory is visible to the operating system. If it is not, determine the amount of memory which may be allocated to the... (3 Replies)
Hi,
I have AIX processes something as below, how to know the resources consumption group by process pattern "price" and "devdb"?
eg:
CPU RAM WIO
price 20% 250M 5%
devdb 30% 1000M 8%
oracle 2990122 1 0 10:33:39 - 0:00... (1 Reply)
Hi Experts,
Our servers running Solaris 10 with SAP Application. The memory utilization always >90%, but the process on SAP is too less even nothing.
Why memory utilization on solaris always looks high?
I have statement about memory on solaris, is this true:
Memory in solaris is used for... (4 Replies)
I am new to AIX, I have few AIX 5.3 servers and I could see there are significant difference in paging space utilization on servers even though they are running same applications
below server is working fine which shows 2-5 % paging usage throuh out the day
cpu_scale_memp = 8... (12 Replies)
Hi All,
I have a java process which is showing high virtual memory utilization in client server. But the same process is showing comparitively lesser virtual memory consumption. I understand that virtual memory shown is not of much importance for the general user in normal condition, my client... (2 Replies)
Discussion started by: mritusmoi
2 Replies
LEARN ABOUT FREEBSD
if_gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD