03-01-2014
I have tried doing this already, using mode=1 and the rest modes, but still have the same flapping in the switches that I have, I have no idea if there any other options in the Linux Server box should I stick with! Thanks anyway..
10 More Discussions You Might Find Interesting
1. Red Hat
Hi,
What is IP bonding in Linux.
What are its advantages
How to create a IP bonding in redhat Linux. (1 Reply)
Discussion started by: chetansingh23
1 Replies
2. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
3. IP Networking
Hello.
Our Company is spreaded over Germany.
There are main offices an branch offices.
These offices are mostly connecte via multiple sdsl.
We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances.
It seemed that only one VPN Connetion between to offices could be... (0 Replies)
Discussion started by: mschwadorf
0 Replies
4. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
5. Hardware
Hi gurus, during playing movie via VLC or SMPlayer I get several time the error that file cannot be read. File was stored on external USB disk. During this error I get another dialogue message that says the new removable disk was connected..., just as if power goes off and on again or if I power on... (1 Reply)
Discussion started by: wakatana
1 Replies
6. Red Hat
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies
7. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
8. Red Hat
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies
9. Red Hat
Dear All ,
Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x.
After configuring , we restarted the network services , the link was down after that , we could not login in to the Server.
So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies
10. Linux
Respected Members,
We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Discussion started by: Mudit Bansal
0 Replies
LEARN ABOUT OSX
set_display_switch_mode
set_display_switch_mode(3alleg4) Allegro manual set_display_switch_mode(3alleg4)
NAME
set_display_switch_mode - Tells Allegro how the program handles background switching.
SYNOPSIS
#include <allegro.h>
int set_display_switch_mode(int mode);
DESCRIPTION
Sets how the program should handle being switched into the background, if the user tabs away from it. Not all of the possible modes will be
supported by every graphics driver on every platform. The available modes are:
SWITCH_NONE
Disables switching. This is the default in single-tasking systems like DOS. It may be supported on other platforms, but you should use it
with caution, because your users won't be impressed if they want to switch away from your program, but you don't let them!
SWITCH_PAUSE
Pauses the program whenever it is in the background. Execution will be resumed as soon as the user switches back to it. This is the default
in most fullscreen multitasking environments, for example the Linux console, but not under Windows.
SWITCH_AMNESIA
Like SWITCH_PAUSE, but this mode doesn't bother to remember the contents of video memory, so the screen, and any video bitmaps that you
have created, will be erased after the user switches away and then back to your program. This is not a terribly useful mode to have, but it
is the default for the fullscreen drivers under Windows because DirectDraw is too dumb to implement anything better.
SWITCH_BACKGROUND
The program will carry on running in the background, with the screen bitmap temporarily being pointed at a memory buffer for the fullscreen
drivers. You must take special care when using this mode, because bad things will happen if the screen bitmap gets changed around when your
program isn't expecting it (see below).
SWITCH_BACKAMNESIA
Like SWITCH_BACKGROUND, but this mode doesn't bother to remember the contents of video memory (see SWITCH_AMNESIA). It is again the only
mode supported by the fullscreen drivers under Windows that lets the program keep running in the background.
Note that you should be very careful when you are using graphics routines in the switching context: you must always call acquire_screen()
before the start of any drawing code onto the screen and not release it until you are completely finished, because the automatic locking
mechanism may not be good enough to work when the program runs in the background or has just been raised in the foreground.
RETURN VALUE
Returns zero on success, invalidating at the same time all callbacks previously registered with set_display_switch_callback(). Returns -1
if the requested mode is not currently possible.
SEE ALSO
set_display_switch_callback(3alleg4), get_display_switch_mode(3alleg4), exmidi(3alleg4), exswitch(3alleg4)
Allegro version 4.4.2 set_display_switch_mode(3alleg4)