02-28-2014
Perhaps there is a firmware pre-requisite. I'm not sure that there really are .exe files on AIX (that VIOS is built on) anyway.
If you have just bought a licence for VIOS, then you should be able to talk to IBM about the problems. If you don't have a licence, IBM will want to talk to you!
Robin (no, I don't work for IBM)
10 More Discussions You Might Find Interesting
1. AIX
I've been trying to get AIX 5.3 installed on a vio partition. I tried one partition that I created, and another one that already had AIX 5.3 on it. In both cases, the install seems to be successful, but when it tries to reboot, it gets to the kernel starting phase, I can see the kernel size, and... (0 Replies)
Discussion started by: Morella
0 Replies
2. AIX
I have a script running remotely using viosvrcmd command on hmc to back up the VIO servers. these are the steps involved
1. Mount the NFS directory on to the VIO server
2. run backupios command
3. un mount the directory
I am stuck up in the 3rd step. I am not able to unmount the nfs... (6 Replies)
Discussion started by: balaji_prk
6 Replies
3. AIX
Hi,
I want to know wheather partition size for installation of vio client can be specified on vio server
example
If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Discussion started by: manoj.solaris
1 Replies
4. AIX
In a dual vio, how will u know one lpar is in which vio? (1 Reply)
Discussion started by: shobhan.murthy
1 Replies
5. AIX
I am planning carving out dual VIO servers on a P750 based and would like to know how to allocate internal disks to the VIOS. This has 4 internal disks and I would to assign 2 disks to each VIO.
This is what I was thinking of assigning . Any advise?
vio1
U5802.001.9K8H757-P1-C1 PCI-E x8... (17 Replies)
Discussion started by: mk8570
17 Replies
6. AIX
I have same lun (hdisk3) assigned to 2 vios server (dual vio server) and this is mapped to the client lpar. I have sddpcm on the VIO.
On the VIOA, the attributes for fscsi1 and fscsi3 are set to fast_fail and dyntrk is set to yes
Now, if I do a lqueryvg -Atp on the hdisk3, I get a "DISK... (4 Replies)
Discussion started by: mk8570
4 Replies
7. Red Hat
I am working in AIX. In a P series machine both aix and linux os can install.. specific command is there for aix to list out the vio servers details mapped in a frame(ie. lssrc "IBM.ManagementServer", like that..) is there any command is der to list out vio servers details in linux or how to find... (1 Reply)
Discussion started by: muralikrish
1 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. AIX
Hi,
I am facing an issue in vio server. When I run
bosboot -ad /dev/hdisk0
I am getting an error
trustchk: Verification of attributes failed: /usr/sbin/bootinfo
: accessauths
regards,
vjm
Please use code tags next time for your code and data. (8 Replies)
Discussion started by: vjm
8 Replies
10. AIX
We've got two datacenters and in every datacenter 2 VIOs.
The VIO manages the I/O of the LPARs. So: Is it possible to reboot the VIO without shuting down an LPAR:wall: (4 Replies)
Discussion started by: DiViN3
4 Replies
LEARN ABOUT DEBIAN
actctrl
ACTCTRL(8) Linux System Administration ACTCTRL(8)
NAME
actctrl - configure IBM Active 2000 ISDN adaptor
SYNOPSIS
actctrl [-d Driver-Id] action options ...
DESCRIPTION
actctrl is used to setup the IBM Active 2000 ISDN device driver and for downloading the firmware into the ISDN card.
The use of actctrl makes sense, if you are using an IBM Active 2000 card only.
OPTIONS
-d Driver-Id
selects the S0 interface named by Driver-Id. Driver-Ids are defined during driver initialisation. See act2000(4) for a description
of the syntax to be used for modularized and monolithic driver versions. This option must be used to identify the S0 interface if
more than one S0 interface is existent. If a single IBM Active 2000 is used, it may be omitted. If using more than one card, sup-
port for the other cards is enabled with the add action of actctrl. Ids may not start with digits or small x, because these values
are misinterpreted as numeric parameters by insmod. For loading the module, always the newest modutils package should be used to
avoid problems during load.
The following actions may be given to actctrl.
add [bus[ port[ irq[ id]]]]
enables support for an additional card in the driver. bus is is an integer describing the bus-type of the card. Currently, the only
value which is allowed here is 1 meaning ISA-bus. In the future, the values 2 (for MCA) and 3 (for PCMCIA) will be available. port
is either an integer describing the base port, or the string auto which enables autoprobing. irq is either an integer describing
the IRQ to use, the string auto, which enables grabbing of the next free IRQ or the string none which enables polled mode for this
card. id is an arbitrary string for referencing the card at a later time.
dproto protocol [msn0,msn1, ... msn9]
selects the D-channel protocol and defines MSN's if using Euro protocol. protocol may be either the string 1tr6 or the string euro.
If selecting Euro protocol, a comma-separated list of up to 10 MSN's may be appended. For defining an empty entry in this list, use
a dash.
load firmware
downloads the firmware into the card and starts operation. Usually the images are located in '/lib/firmware/isdn'. The firmware is
named bip1120.bpl.
dump is available if the program is configured using the --enable-dump option only. The contents of internal driver variables is dumped
on stdout.
FILES
'/lib/firmware/isdn'/bip1120.bpl
This is the image of the firmware designed for both the German 1TR6 protocol and Euro ISDN.
BUGS
No bugs so far.
AUTHOR
(C) 1997 by Fritz Elfert <fritz@isdn4linux.de>
SEE ALSO
isdnctrl(8), act2000(4), isdnctrl(4), ttyI(4).
isdn4k-utils-3.9 1999/09/06 ACTCTRL(8)