Sponsored Content
Full Discussion: Problems with VIO O/S 2.2.3
Operating Systems AIX Problems with VIO O/S 2.2.3 Post 302890704 by johnf on Friday 28th of February 2014 06:32:16 AM
Old 02-28-2014
Problems with VIO O/S 2.2.3

I hope someone has experienced this problem before and can help. I have a P730 (8231-E2D) which is fitted with 8 IBM SAS disks on 2 separate SISSAS controllers. The disk type is ST9146853SS (Seagate SAS 146Gb).

The problem occurs when I try to install the VIO server software at 2.2.3. It fails to correctly install and the file systems (if they load at all) are corrupted with a lot of the .exe files missing!

I load it from a mksysb on the NIM server with the SPOT created from the mksysb. I have used the same mksysb this morning to build a VIO server on a P750 and it worked correctly

Anyone help please?
 

10 More Discussions You Might Find Interesting

1. AIX

Problems installing AIX on vio

I've been trying to get AIX 5.3 installed on a vio partition. I tried one partition that I created, and another one that already had AIX 5.3 on it. In both cases, the install seems to be successful, but when it tries to reboot, it gets to the kernel starting phase, I can see the kernel size, and... (0 Replies)
Discussion started by: Morella
0 Replies

2. AIX

Backup of VIO

I have a script running remotely using viosvrcmd command on hmc to back up the VIO servers. these are the steps involved 1. Mount the NFS directory on to the VIO server 2. run backupios command 3. un mount the directory I am stuck up in the 3rd step. I am not able to unmount the nfs... (6 Replies)
Discussion started by: balaji_prk
6 Replies

3. AIX

vio server and vio client

Hi, I want to know wheather partition size for installation of vio client can be specified on vio server example If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Discussion started by: manoj.solaris
1 Replies

4. AIX

vio related

In a dual vio, how will u know one lpar is in which vio? (1 Reply)
Discussion started by: shobhan.murthy
1 Replies

5. AIX

Vio Build

I am planning carving out dual VIO servers on a P750 based and would like to know how to allocate internal disks to the VIOS. This has 4 internal disks and I would to assign 2 disks to each VIO. This is what I was thinking of assigning . Any advise? vio1 U5802.001.9K8H757-P1-C1 PCI-E x8... (17 Replies)
Discussion started by: mk8570
17 Replies

6. AIX

sddpcm on vio

I have same lun (hdisk3) assigned to 2 vios server (dual vio server) and this is mapped to the client lpar. I have sddpcm on the VIO. On the VIOA, the attributes for fscsi1 and fscsi3 are set to fast_fail and dyntrk is set to yes Now, if I do a lqueryvg -Atp on the hdisk3, I get a "DISK... (4 Replies)
Discussion started by: mk8570
4 Replies

7. Red Hat

vio in linux

I am working in AIX. In a P series machine both aix and linux os can install.. specific command is there for aix to list out the vio servers details mapped in a frame(ie. lssrc "IBM.ManagementServer", like that..) is there any command is der to list out vio servers details in linux or how to find... (1 Reply)
Discussion started by: muralikrish
1 Replies

8. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies

9. AIX

VIO Server

Hi, I am facing an issue in vio server. When I run bosboot -ad /dev/hdisk0 I am getting an error trustchk: Verification of attributes failed: /usr/sbin/bootinfo : accessauths regards, vjm Please use code tags next time for your code and data. (8 Replies)
Discussion started by: vjm
8 Replies

10. AIX

Reboot VIO - OK?

We've got two datacenters and in every datacenter 2 VIOs. The VIO manages the I/O of the LPARs. So: Is it possible to reboot the VIO without shuting down an LPAR:wall: (4 Replies)
Discussion started by: DiViN3
4 Replies
MPT(4)							   BSD Kernel Interfaces Manual 						    MPT(4)

NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device mpt Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): mpt_load="YES" DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers. HARDWARE
The following controllers are supported by the mpt driver: o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI) o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA) o LSI Logic FC909 (1Gb/s Fibre Channel) o LSI Logic FC909A (Dual 1Gb/s Fibre Channel) o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel) o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel) o LSI Logic FC949X (Dual 4Gb/s Fibre Channel) o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express) The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including: o Dell PowerEdge 1750 thru 2850 o IBM eServer xSeries 335 These systems also contain Integrated RAID Mirroring and Integrated RAID Mirroring Enhanced which this driver also supports. The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both SAS and SATA drives or a mix of them at the same time. The Integrated RAID Mirroring available for these controllers is poorly supported at best. The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the FC949ES card. This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required. SEE ALSO
cd(4), ch(4), da(4), mps(4), pci(4), sa(4), scsi(4), targ(4), gmultipath(8), mptutil(8) LSI Logic Website, http://www.lsi.com/. HISTORY
The mpt driver first appeared in FreeBSD 4.6. AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>. Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements. BSD
July 23, 2011 BSD
All times are GMT -4. The time now is 05:47 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy