Sponsored Content
Full Discussion: BONDING with Flapping issue!
Operating Systems Linux Red Hat BONDING with Flapping issue! Post 302890496 by MadeInGermany on Thursday 27th of February 2014 05:45:54 AM
Old 02-27-2014
Got this by googling:
If you are using the load balancing channel bonding, your router may complaint that the MAC address is flip flopping because the same MAC address is appearing in two different links.
If the use of load balancing is purely for redundancy, consider using active standby mode (mode=1). If not, most likely you have to work on your router configuration.
 

10 More Discussions You Might Find Interesting

1. Red Hat

IP Bonding

Hi, What is IP bonding in Linux. What are its advantages How to create a IP bonding in redhat Linux. (1 Reply)
Discussion started by: chetansingh23
1 Replies

2. IP Networking

Channel bonding Issue - Bond0 interface not getting up in on RHEL6

Hello, I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies

3. IP Networking

Bonding of IP tunnels

Hello. Our Company is spreaded over Germany. There are main offices an branch offices. These offices are mostly connecte via multiple sdsl. We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances. It seemed that only one VPN Connetion between to offices could be... (0 Replies)
Discussion started by: mschwadorf
0 Replies

4. Linux

ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0. Here's what I did: created file /etc/modprobe.d/bonding.d and added the following to it: alias bond0 bonding options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies

5. Hardware

Flapping (reconnecting) external USB drive

Hi gurus, during playing movie via VLC or SMPlayer I get several time the error that file cannot be read. File was stored on external USB disk. During this error I get another dialogue message that says the new removable disk was connected..., just as if power goes off and on again or if I power on... (1 Reply)
Discussion started by: wakatana
1 Replies

6. Red Hat

Bonding a Bond with LACP

Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies

7. IP Networking

Is bond0 ready and a bonding interface? - 4G Bonding Router Problems (RPI)

HI all, First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place. I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies

8. Red Hat

Network Bonding Issue

I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies

9. Red Hat

Network bonding

Dear All , Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x. After configuring , we restarted the network services , the link was down after that , we could not login in to the Server. So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies

10. Linux

Issue in Bonding during Reboot(Linux)

Respected Members, We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Discussion started by: Mudit Bansal
0 Replies
Match-all classifier in tc(8)                                          Linux                                         Match-all classifier in tc(8)

NAME
matchall - traffic control filter that matches every packet SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ] DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it. OPTIONS
action ACTION_SPEC Apply an action from the generic actions framework on matching packets. classid CLASSID Push matching packets into the class identified by CLASSID. skip_sw Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter- face, operation will fail. skip_hw Do not process filter by hardware. EXAMPLES
To create ingress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle ffff: ingress tc filter add dev eth1 parent ffff: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To create egress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle 1: root prio tc filter add dev eth1 parent 1: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To sample one of every 100 packets flowing into interface eth0 to psample group 12: tc qdisc add dev eth0 handle ffff: ingress tc filter add dev eth0 parent ffff: matchall action sample rate 100 group 12 SEE ALSO
tc(8), iproute2 21 Oct 2015 Match-all classifier in tc(8)
All times are GMT -4. The time now is 02:58 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy