Issue with ethernet interface Post: 302890256

10 More Discussions You Might Find Interesting

1. Programming

determine if a ethernet interface is up

Howto check if a ethernet interface is up? It's impossible to determine via the ipaddress i have learned, or? Can someone please give me a hint on howto do? Environment == Linux x86 GNU GCC. :D regards Esaia

2. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such...

3. Solaris

Network Interface Issue

Hi all, Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP. - - - -- --...

4. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance

5. Solaris

Network interface issue

Hi All, I want to configure network into my system. i tried following in to configure the interface to find the name of interface #prtdiag |grep net i got following 0 PCI-1 33 1 network-SUNW, hme then i tried following #prtconf -v |grep net network, instance #0

6. Solaris

Sun Solaris ethernet interface

Hi, During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured, what is way to find out how many ethernet interfaces are there on Server,

7. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

8. AIX

interface collisions on ethernet nic

Hi, is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this. Thanks&regards, p

9. IP Networking

Channel bonding Issue - Bond0 interface not getting up in on RHEL6

Hello, I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my...

10. UNIX for Advanced & Expert Users

C program to detect duplicate ip address if any after assigning ip address to ethernet interface

Hi , Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program

LEARN ABOUT DEBIAN

bpqparms

BPQPARMS(8)						   Linux System Managers Manual 					       BPQPARMS(8)

NAME

       bpqparms - Configure BPQ ethernet devices.

SYNOPSIS

       bpqparms device [-a ethaddr] [-d ethaddr] [-vV]

DESCRIPTION

       Bpqparms  allows  the  setting  of  the	BPQ  Ethernet  options for a particular device. Each BPQ Ethernet device appears as a device named
       bpq0...bpqN which overlays the original Ethernet device, usually eth0...ethN. This device is an AX.25 device driver and allows AX.25 frames
       to be transmitted over an Ethernet to another machine using the same protocol. The default for the device is to send and receive BPQ Ether-
       net packets to the broadcast address. This program replaces the previous "axparms -dev" option.

OPTIONS

       -a ethaddr     Allows the setting of which ethernet address will be accepted by the BPQ Ethernet device.

       -d ethaddr     If specified on its own, will set the destination ethernet address will be used for transmitting and for	receiving  of  BPQ
		      ethernet packets. An address of "broadcast" sets it to the ethernet broadcast address.

       -v	      Displays the version number.

       -V	      The original version messages.

SEE ALSO

       ax25(4), axports(5), ifconfig(8).

AUTHOR

       Joerg Reuter DL1BKE <jreuter@poboxes.com>

Linux								 4 September 1996						       BPQPARMS(8)

10 More Discussions You Might Find Interesting

1. Programming

determine if a ethernet interface is up

Discussion started by: Esaia

2. SCO

Issue with a ethernet card

Discussion started by: tazmss1

3. Solaris

Network Interface Issue

Discussion started by: baraghun

4. Solaris

Ethernet card drivers issue...

Discussion started by: younus_syed