ethtool can tell you the capabilities of a network device.
Code:
# ethtool lan
Settings for lan:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: MII
PHYAD: 3
Transceiver: external
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Link detected: yes
#
I have an application that requires me to disable the restricted access to the X Server libraries by issuing the 'Xhost +' command from a Console Window.
It is important that this command is run from the Console Window and not a Terminal Window otherwise the system complains that DISPLAY is not... (0 Replies)
ello all..
I really have a big problem installing debian 4.0 on HP dl380 G5 ,2 74 sScsi in raid 1 (mirror), after all selected options, it's freezes on getting files 125 of 125 and stops on 5% of the installation. I've try with different cd's and cd-roms so that's not the problem! Can someone... (4 Replies)
1) Does anyone know IF HP Proliant DL380 G3 is compatible to install Solaris 10 - as whenever I tried to install, it gives an error saying 'No disk found' after keying in date/time etc.
2) I found somewhere that text installation will be able to fix it - What is text installation?
Thank you (7 Replies)
Trying to install Openserver 6.0 on this server which has an integrated Smart Array P400.
Install halts with the message .......
"Incorrect Disk Partitioning .........................."
I havent yet got to the "divvy" and disk partitioning section of the install section so I am... (2 Replies)
Hello,
I have a few questions about this server.
It has two CPU's 3.20 ghz / 800 mhz / 1MB L2
5120 MB RAM
6 hard disks on HP Smart Array 6i controller (36.4 GB Ultra320 SCSI HD each)
RAID set to RAID 5 (5 discs) with one spare (6th disk)
USB, 2 Ethernet ports, 1 ILO port, 1 SCSI port
... (2 Replies)
I have 2 DL380g6 servers, one server has a riser kit installed and the other does not. running rhel5.6, how from the OS can I see the riser kit is installed? lspci didn't list the riser kit, but then again I'm not entirely sure its classified as a pci device? Is there a way to see it from the OS (1 Reply)
Hi,
I want to do momentary press to one server from linux is it possible? I got this command from internet is it correct? or need changes? I also need help how to start and reboot server in hp ilo from linux server.
fence_ilo -a 10.1.41.155 -l Admin -p Password (1 Reply)
I'm running glusterfs on CentOS 6.6 two nodes, (the SSD (samsung 840 1TB x2) is RAID 0 on the HP DL380 G6) x2, and trimming is not enable on it by checking /dev/sdb1/xxxxx/discard_max_bytes=0. Do I still need trimming? Somehow my filesystem is fine with 35-30% free space and running very fast.
... (1 Reply)
Discussion started by: itik
1 Replies
LEARN ABOUT MINIX
txp
TXP(4) BSD Kernel Interfaces Manual TXP(4)NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device txp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_txp_load="YES"
DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset.
Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload-
ing, tcp(4) segmentation, nor ipsec(4) acceleration.
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu-
tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of
attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.
The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are:
media autoselect
Attempt to autoselect the media type (default)
media 100baseTX mediaopt full-duplex
Use 100baseTX, full duplex
media 100baseTX [mediaopt half-duplex]
Use 100baseTX, half duplex
media 10baseT mediaopt full-duplex
Use 10baseT, full duplex
media 10baseT [mediaopt half-duplex]
Use 10baseT, half duplex
HARDWARE
The txp driver supports the following cards:
o 3Com 3CR990-TX-95
o 3Com 3CR990-TX-97
o 3Com 3cR990B-TXM
o 3Com 3CR990SVR95
o 3Com 3CR990SVR97
o 3Com 3cR990B-SRV
SEE ALSO altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8)HISTORY
The txp driver first appeared in OpenBSD 2.9.
BSD March 12, 2009 BSD