I have a problem in searching a specific pattern in c files.
My requirement:
I have to find all the division operator in all cfiles.
The problem is, the multi line comments and single line comments will also have forward slash in it.
Even after avoiding these comments also, if both... (6 Replies)
Hi All,
Please can someone assist in the script I have made that searches a pattern in a file and delete the whole line containing the pattern.
#!bin/sh
# The pattern that user want to add to the files
echo "Enter the pattern of the redirect"
read value
# check if the user has... (1 Reply)
Hi Experts,
Need help on printing of numbers, which are missing in the range.
Pls find the details below
Input
1000000002
1000000007
1234007940
1234007946
Output
1000000003
1000000004
1000000005
1000000006
1234007941 (2 Replies)
Hi...
I am working on script to search some records in a file based on certain fields and each record is a ASCII fixed size. I was using awk to search based on certain condition. But the length of the record is too much that awk is giving
syntax error near unexpected token `('
Request... (5 Replies)
Hi there,
Looking forward to your advice for the below:
I have a file which contains 2 paragraphs related to a particular pattern. I have to search for those paragraphs from a log file and then print a particular line from those paragraphs.
Sample:
I have one file with the fixed... (3 Replies)
Hi All,
i have an output of command vmstat as below :
$ vmstat
System configuration: lcpu=4 mem=5376MB ent=1.00
kthr memory page faults cpu
----- ----------- ------------------------ ------------ -----------------------
r b avm fre re pi... (10 Replies)
i m searching a zone file my domain name is abcd.com
my zone file looks like this.
abcd.com. IN SOA ns1.abcd.com. root.abcd.com. (
abcd.com. 400 IN A 15.1.1.1
Then i am searching that abcd.com have if below ip... (14 Replies)
'Hi
I'm using the following code to extract the lines(and redirect them to a txt file) after the pattern match. But the output is inclusive of the line with pattern match.
Which option is to be used to exclude the line containing the pattern?
sed -n '/Conn.*User/,$p' > consumers.txt (11 Replies)
Hi All,
I 'm matching two files based on the first 2 columns and then populate other fields along with subtraction of few fields.
I have managed to get the output. However, is there a easier way in formatting the output as shown below instead of using additional printf for getting fixed width... (4 Replies)
This is the file which contains only neccessary values from the output of curl command i.e TEMP_FILE
Proxy Hostname
server0123.domain.com
Proxy IP address
XXX.XXX.XX.XX port 0000
Proxy Version
SGOS X.X.X.X
Proxy Serial #
... (5 Replies)
Discussion started by: ramprabhum
5 Replies
LEARN ABOUT CENTOS
cpupower-set
CPUPOWER-SET(1) cpupower Manual CPUPOWER-SET(1)NAME
cpupower-set - Set processor power related kernel or hardware configurations
SYNOPSIS
cpupower set [ -b VAL ] [ -s VAL ] [ -m VAL ]
DESCRIPTION
cpupower set sets kernel configurations or directly accesses hardware registers affecting processor power saving policies.
Some options are platform wide, some affect single cores. By default values are applied on all cores. How to modify single core configura-
tions is described in the cpupower(1) manpage in the --cpu option section. Whether an option affects the whole system or can be applied to
individual cores is described in the Options sections.
Use cpupower info to read out current settings and whether they are supported on the system at all.
Options--perf-bias, -b
Sets a register on supported Intel processore which allows software to convey its policy for the relative importance of performance
versus energy savings to the processor.
The range of valid numbers is 0-15, where 0 is maximum performance and 15 is maximum energy efficiency.
The processor uses this information in model-specific ways when it must select trade-offs between performance and energy efficiency.
This policy hint does not supersede Processor Performance states (P-states) or CPU Idle power states (C-states), but allows software to
have influence where it would otherwise be unable to express a preference.
For example, this setting may tell the hardware how aggressively or conservatively to control frequency in the "turbo range" above the
explicitly OS-controlled P-state frequency range. It may also tell the hardware how aggressively it should enter the OS requested C-
states.
This option can be applied to individual cores only via the --cpu option, cpupower(1).
Setting the performance bias value on one CPU can modify the setting on related CPUs as well (for example all CPUs on one socket),
because of hardware restrictions. Use cpupower -c all info -b to verify.
This options needs the msr kernel driver (CONFIG_X86_MSR) loaded.
--sched-mc, -m [ VAL ]
--sched-smt, -s [ VAL ]
--sched-mc utilizes cores in one processor package/socket first before processes are scheduled to other processor packages/sockets.
--sched-smt utilizes thread siblings of one processor core first before processes are scheduled to other cores.
The impact on power consumption and performance (positiv or negativ) heavily depends on processor support for deep sleep states, fre-
quency scaling and frequency boost modes and their dependencies between other thread siblings and processor cores.
Taken over from kernel documentation:
Adjust the kernel's multi-core scheduler support.
Possible values are:
0 - No power saving load balance (default value)
1 - Fill one thread/core/package first for long running threads
2 - Also bias task wakeups to semi-idle cpu package for power savings
SEE ALSO cpupower-info(1), cpupower-monitor(1), powertop(1)AUTHORS --perf-bias parts written by Len Brown <len.brown@intel.com>
Thomas Renninger <trenn@suse.de>
22/02/2011 CPUPOWER-SET(1)