01-21-2014
Just going to follow up with what I did in hopes it helps someone else who has this issue arise.
Use diag command to check array and find failed disk(s).
# diag
---> Task Selection
---> RAID Array Manager
---> PCI-X SCSI Disk Array Manager
---> List PCI-X SCSI Disk Array Configuration
---> sisioa1 Available 06-08 PCI-X Dual Channel U320 SCSI RAID
Activate the LED indicator of the physical disk to locate it on the rack.
# diag
---> Task Selection
---> Hot Plug Task
---> SCSI and SCSI RAID Hot Plug Manager
---> Replace/Remove a Device Attached to an SCSI Hot Swap Enclosure
---> select failed disk here(pdisk#)
A message will appear in regards to an LED and Remove state. Find the physical drive that is now flashing amber from its LED and remove it from the array. After you remove the failed physical drive, replace it with the new unit.
Hit Enter on that message screen to remove that slot from the "remove state".
# diag
---> Task Selection
---> Hot Plug Task
---> SCSI and SCSI RAID Hot Plug Manager
---> Configure Added/Replaced Devices
# diag
---> Task Selection
---> Log Repair Action (Select affected disk)
Rebuild the array
# diag
---> Task Selection
---> RAID Array Manager
---> PCI-X SCSI Disk Array Manager
---> Reconstruct a PCI-X SCSI Disk Array
These 2 Users Gave Thanks to mpeter05 For This Post:
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
AIX 4.3.3
I am investigating methods of creating system backups. One method I am investigating is installing a hot swap hard drive and creating a mksysb to that hard drive. Does anyone have any ideas on getting this accomplished? I am thinking that I need a mounted file system from the 2nd... (0 Replies)
Discussion started by: jalburger
0 Replies
2. UNIX for Advanced & Expert Users
Hey everyone,
first of all, this is the motherboard I have: GigaByte GA-K8NXP-9 , nForce4 Ultra. It supports RAID 0, 1, 0+1 apparently both on the IDE and S-ATA HDD.
Now what I had in mind is popping 2 x 6Gb HDD in the IDE slots as slave 1 & 2 where my 2 DVD/CD burners are master. I then plan... (2 Replies)
Discussion started by: temba
2 Replies
3. UNIX for Dummies Questions & Answers
How do you view Drive/RAID configuration in UNIX?
We are running an ML370 with 6 drives in it...
Version: Sco 5.2.0
Sco Openserver Release 5 (2 Replies)
Discussion started by: bpoulson
2 Replies
4. OS X (Apple)
I am trying to recover data off a drive that failed in my iMac. Apple returned the drive to me and I purchased a hard drive enclosure. I have been doing research on prices for data recovery services, way too expensive. I seen some links using Unix DD commands in the terminal none of which worked.... (6 Replies)
Discussion started by: KJ1906
6 Replies
5. UNIX for Dummies Questions & Answers
Hello,
I have a machine that has software based RAID. One of the hard drives failed. The problem is that the old systems administrator created LVM and then RAID. My understanding is that RAID had to be created before and then the LVM's. Is there someway to install the new drive without loosing... (2 Replies)
Discussion started by: mojoman
2 Replies
6. Hardware
Hey All,
Im using Fedora 2.6 (which is cannot be changed for compatibility reasons).
I cloned a drive from a different server and when i added this drive to a new box, during startup it hangs on "Configuring Kernel Parameters:"
Is there any way to bypass this process and still boot... (0 Replies)
Discussion started by: robfwauk
0 Replies
7. Hardware
I am having trouble connecting my 4TB G-Raid Hard drive to my Compaq Hp laptop can anyone tell me how or what I need in order to connect the 4T and getting it working. (10 Replies)
Discussion started by: Jake Wolf
10 Replies
8. SCO
Our tape drive died and I installed a newer Quantum DAT72 drive in it's place with the same SCSI ID. It still works, but with one major flaw, the system will lock up if I try to upgrade BackupEDGE or view NFS settings in scoadmin.
I get a Transition to ready failure on ha=0* message when the... (4 Replies)
Discussion started by: psytropic
4 Replies
9. UNIX for Advanced & Expert Users
Good Evening,
2 years ago, I set up an Ubuntu file-server for a friend, who is a photograph amateur. Basically, the server offers a software RAID-5 that can be accessed remotely from a MAC. Unfortunately, I didn't labeled the hard drives (i.e. which physical drive corresponds to the /dev/sdX... (2 Replies)
Discussion started by: Loic Domaigne
2 Replies
10. Filesystems, Disks and Memory
I found out that the raid 1 was degraded:
# cat /proc/mdstat
Personalities :
md3 : active raid1 sda5 sdb5
1822445428 blocks super 1.0
md2 : active raid1 sda3(F) sdb3
1073741688 blocks super 1.0
md1 : active raid1 sda2 sdb2
524276 blocks super 1.0
md0 : active raid1 sda1... (0 Replies)
Discussion started by: ZaNaToS
0 Replies
AAC(4) BSD Kernel Interfaces Manual AAC(4)
NAME
aac -- Adaptec AdvancedRAID Controller driver
SYNOPSIS
aac* at pci? dev ? function ?
ld* at aac? unit ?
DESCRIPTION
The aac driver provides support for the Adaptec AAC family of SCSI and SATA RAID controllers. These controllers support RAID 0, 1, 5, 10,
and volume sets. They have four channels in the add-in version or 1-2 channels in the motherboard integrated version, and are most often
found rebadged by Dell, Hewlett-Packard or IBM. Supported controllers include:
o Adaptec AAC-364
o Adaptec SCSI RAID 2120S
o Adaptec SCSI RAID 2200S
o Adaptec SATA RAID 2410SA
o Adaptec SATA RAID 3405
o Adaptec SCSI RAID 5400S
o Dell PERC 2/Si
o Dell PERC 2/QC
o Dell PERC 3/Di
o Dell PERC 3/Si
o Dell PERC 320/DC
o Dell CERC SATA RAID 1.5/6ch
o HP NetRAID 4M
o HP ML110 G2 (Adaptec SATA RAID 2610SA)
o IBM ServeRAID 8k
Access to RAID containers is available via the ld device driver. Individual drives cannot be accessed unless they are part of a container or
volume set, and non-fixed disks cannot be accessed. Containers can be configured by using the on-board BIOS utility of the card.
DIAGNOSTICS
The adapter can send status and alert messages asynchronously to the driver. These messages are printed on the system console.
SEE ALSO
intro(4), ld(4)
HISTORY
The aac driver first appeared in NetBSD 1.6, and was based on the FreeBSD driver of the same name.
BUGS
This driver is not compatible with controllers that have version 1.x firmware. The firmware version is the same as the kernel version
printed in the BIOS POST and driver attach messages.
BSD
February 19, 2011 BSD