Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Hi,
I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command:
#ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0
#add route or route add default xxx.xxx.xxx.xxx
In Solaris 10, I believe the commands are... (7 Replies)
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
LEARN ABOUT OPENSOLARIS
net_phygetnext
net_phygetnext(9F) Kernel Functions for Drivers net_phygetnext(9F)NAME
net_phygetnext - search through the current list of network interfaces
SYNOPSIS
#include <sys/neti.h>
phy_if_t net_phygetnext(const net_data_t net, const phy_if_t ifp);
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI).
PARAMETERS
net value returned from a successful call to net_protocol_lookup(9F).
ifp value returned from a successful call to this function or net_phylookup(9F).
DESCRIPTION
The net_phygetnext() function searches through all of the network interfaces that a network protocol "owns". To start searching through all
of the interfaces owned by a protocol, a value of 0 should be passed through as the value of ifp. When 0 is returned by this function, the
last of the interfaces owned by this protocol has been reached.
When called successfully, the value returned represents a network interface that exists, at the time of the call, within the scope of the
network interface. This value is only guaranteed to be unique for a name within the scope of the network protocol.
EXAMPLES
net_data_t net;
phy_if_t ifp;
char buffer[32];
net = net_protocol_lookup("inet");
if (net != NULL) {
for (ifp = net_phygetnext(net, 0); ifp != 0;
ifp = net_phygetnext(net, ifp)) {
/* Do something with ifp */
if (net_getifname(net, ifp, buffer,
sizeof(buffer) >= 0)
printf("Interface %s0, buffer);
}
}
RETURN VALUES
The net_phygetnext() function returns -1 if it is not supported by the network protocol or 0 if an attempt to go beyond the last network
interface is made. Otherwise, it returns a value representing a network interface.
CONTEXT
The net_phygetnext() function may be called from user, kernel, or interrupt context.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Committed |
+-----------------------------+-----------------------------+
SEE ALSO net_phylookup(9F), net_protocol_lookup(9F), attributes(5)SunOS 5.11 1 May 2008 net_phygetnext(9F)