Hi. What command can be used to determine the system
configuration. For example I want to find out how much CPU,
how much memory, what CPU and 233mhz or 400mhz, etc.
Please help.... (4 Replies)
Hi Gurus!
I recently got my shell account (HP UX v11) created by our sysadmin and am having problem deleting with the backspace key.
After doing some reading, I believe I need to enter a custom "STTY..." statement in my profile.
Can someone please help me with the correct "STTY" sequence... (3 Replies)
Okay here is a DOS comparison. When I search for a file in DOS and I was not sure what directory it was in then I would put dir /s/o/p filename the s would tell it to look in every directory including subs, the o would sort it alphabetically and the p would limit the display to one page at a... (1 Reply)
Hello,
I create a file touch 1201093003 fichcomp
and inside a repertory (which hava a lot of files) I want to list all files created before this file :
find *.* \! -maxdepth 1 - newer fichcomp but this command returned bash: /usr/bin/find: Argument list too long
but i make a filter all... (1 Reply)
The purpose of those comands are to find the newest file in a directory acvrdind to system date, and it has to be recursively found in each directory.
The problem is that i want to list in a long format every found file, but the commands i use produce unexpected results ,so the output lists in a... (5 Replies)
Hi All,
I need to list the files based modification time of the files from a directory, I cannot use "ls -t" as there are lot of files, which "ls" command cannot handle. New files will land there daily. So iam looking for an alternative through "find"command.
All suggestions are welcomed.
... (6 Replies)
hi,
i want to list the files from the below find commands output.
find ./* -name "*.txt" -type f -mtime +10
will give the output like
./a.txt
but i need the output in the format like (ls -lrt a.txt )
-rw-rw-rw- 1 srea nast 5 May 23 07:34 a.txt
i used xargs for the... (4 Replies)
I need to find a word '% Retail by State' in the folder /usr/sas/reports/RetailSalesTaxallocation.
When I tried like below,
-bash-4.1$ cd /usr/sas/reports/RetailSalesTaxallocation
-bash-4.1$ find ./ -name % Retail by State
find: paths must precede expression: Retail
Usage: find ... (10 Replies)
Discussion started by: Ram Kumar_BE
10 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)