Hi. What command can be used to determine the system
configuration. For example I want to find out how much CPU,
how much memory, what CPU and 233mhz or 400mhz, etc.
Please help.... (4 Replies)
Hi Gurus!
I recently got my shell account (HP UX v11) created by our sysadmin and am having problem deleting with the backspace key.
After doing some reading, I believe I need to enter a custom "STTY..." statement in my profile.
Can someone please help me with the correct "STTY" sequence... (3 Replies)
Okay here is a DOS comparison. When I search for a file in DOS and I was not sure what directory it was in then I would put dir /s/o/p filename the s would tell it to look in every directory including subs, the o would sort it alphabetically and the p would limit the display to one page at a... (1 Reply)
Hello,
I create a file touch 1201093003 fichcomp
and inside a repertory (which hava a lot of files) I want to list all files created before this file :
find *.* \! -maxdepth 1 - newer fichcomp but this command returned bash: /usr/bin/find: Argument list too long
but i make a filter all... (1 Reply)
The purpose of those comands are to find the newest file in a directory acvrdind to system date, and it has to be recursively found in each directory.
The problem is that i want to list in a long format every found file, but the commands i use produce unexpected results ,so the output lists in a... (5 Replies)
Hi All,
I need to list the files based modification time of the files from a directory, I cannot use "ls -t" as there are lot of files, which "ls" command cannot handle. New files will land there daily. So iam looking for an alternative through "find"command.
All suggestions are welcomed.
... (6 Replies)
hi,
i want to list the files from the below find commands output.
find ./* -name "*.txt" -type f -mtime +10
will give the output like
./a.txt
but i need the output in the format like (ls -lrt a.txt )
-rw-rw-rw- 1 srea nast 5 May 23 07:34 a.txt
i used xargs for the... (4 Replies)
I need to find a word '% Retail by State' in the folder /usr/sas/reports/RetailSalesTaxallocation.
When I tried like below,
-bash-4.1$ cd /usr/sas/reports/RetailSalesTaxallocation
-bash-4.1$ find ./ -name % Retail by State
find: paths must precede expression: Retail
Usage: find ... (10 Replies)
Discussion started by: Ram Kumar_BE
10 Replies
LEARN ABOUT BSD
css
CSS(4) Kernel Interfaces Manual CSS(4)NAME
css - DEC IMP-11A LH/DH IMP interface
SYNOPSIS
/sys/conf/SYSTEM:
NCSS css_controllers # DEC/CSS IMP11-A ARPAnet IMP interface
DESCRIPTION
The css device provides a Local Host/Distant Host interface to an IMP. It is normally used when participating in the DARPA Internet. The
controller itself is not accessible to users, but instead provides the hardware support to the IMP interface described in imp(4). When
configuring, the imp(NIMP) pseudo-device is also included.
DIAGNOSTICS
css%d: not alive. The initialization routine was entered even though the device did not autoconfigure. This is indicates a system prob-
lem.
css%d: can't initialize. Insufficient UNIBUS resources existed to initialize the device. This is likely to occur when the device is run
on a buffered data path on an 11/750 and other network interfaces are also configured to use buffered data paths, or when it is configured
to use buffered data paths on an 11/730 (which has none).
css%d: imp doesn't respond, icsr=%b. The driver attempted to initialize the device, but the IMP failed to respond after 500 tries. Check
the cabling.
css%d: stray output interrupt csr=%b. An interrupt occurred when no output had previously been started.
css%d: output error, ocsr=%b icsr=%b. The device indicated a problem sending data on output.
css%d: recv error, csr=%b. The device indicated a problem receiving data on input.
css%d: bad length=%d. An input operation resulted in a data transfer of less than 0 or more than 1008 bytes of data into memory (according
to the word count register). This should never happen as the maximum size of a host-IMP message is 1008 bytes.
3rd Berkeley Distribution August 20, 1987 CSS(4)