Dear ALL,
my server give me messages like below:
Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off
I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Hi Community,
I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output:
# ifconfig hme0 <ip_address> netmask <mask> plumb
#ifconfig: plumb: hme0: no such interface
I've the same thing with dhcp service.
could you provide any solution... (1 Reply)
hi all,
i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT HPUX
show_cached_clearinghouse
show cached clearinghouse(1m) show cached clearinghouse(1m)NAME
show cached clearinghouse - Displays current information about the specified cached clearinghouse
SYNOPSIS
cdscp show cached clearinghouse clearinghouse-name
ARGUMENT
A specific clearinghouse name. The name can contain wildcard characters.
DESCRIPTION
The show cached clearinghouse command displays all the names and values of the attributes in the specified cached clearinghouse. The fol-
lowing are valid attributes: Specifies the time at which this clearinghouse was added to the cache Specifies the number of operations other
than read and write (that is, skulks, new epochs, and so on) performed by this clerk on the cached clearinghouse Specifies the number of
lookup operations of any sort performed by the clerk on the cached clearinghouse Specifies the protocol sequence and Internet address of
the server that maintains the cached clearinghouse Specifies the number of write operations performed by this clerk on the cached clearing-
house
Privilege Required
You must have read permission to the clerk.
NOTE
This command is replaced at Revision 1.1 by the dcecp command and may not be provided in future releases of DCE.
EXAMPLE
The following command displays all attributes of the cached clearinghouse /.:/Paris2_CH. cdscp> show cached clearinghouse /.:/Paris2_CH
SHOW
CACHED CLEARINGHOUSE /.../abc.com/Paris2_CH
AT 1991-10-15-15:58:09
Creation Time = 1991-10-01-17:03:32.32
Read Operations = 412
Write Operations = 618
Miscellaneous Operations = 278
RELATED INFORMATION
Commands: list clearinghouse(1m)
show cached clearinghouse(1m)