To Delete an iSCSI discovery target IP address from the kernel registry, use:
# iscsiutil [/dev/iscsi] -d -I <ip-address> [-P <tcp-port>][-M <portal-grp-tag>]
<ip-address> The ip_address specified can be an IPv4 formatted address or a DNS name
<tcp-port> A TCP port may be specified for the iSCSI target. If no port is specified, the default iSCSI target port (3260) will be used.
<portal-grp-tag> The target portal group tag may be specified (a value from 0 to 65535 inclusive); otherwise a default value of 1 will be used.
---------- Post updated at 03:45 AM ---------- Previous update was at 03:37 AM ----------
the error shows IP "192.168.1.252" do not find .
maybe you execute
and reexecute the command to delete the lun.
Hi all
iscsiadm / iscsitadm.
Ive created two devices on a host.
# iscsitadm list target
Target: 1-disk0
iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0
Connections: 1
Target: 1-disk1
iSCSI Name:... (0 Replies)
Hello,
I am trying to breakdown the cXtXdX (specifically tX) part of an iscsi device.
I know in the fibre SAN world, this tX will usually be a combination of the path to device/device WWN.
From what I understand in iscsi world it is similar, breaking down into... (0 Replies)
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Hi all,
I have a text file with a lot of records.
In each records I have tags like this:
=952 \\$aBNCS-CH\\$bBNCS-CH\\$h1989\\$oBNCS-CH0000001\\$pBNCS-CH0000001\\$yJNL
=952 \\$aBNCS-C.UNIV\\$bBNCS-C.UNIV\\$h1974-77.\\$oBNCS-C.UNIV0000001\\$pBNCS-C.UNIV0000001\\$yJNL
=952... (4 Replies)
hi all,
i'm new here and i have a question,
i wanted to know, what should happen if i delete a LUN that is already mounted on one of my initiators.
thanks! (3 Replies)
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
rsync with --delete won't honor the delete if the source is something/*. I want the delete to work, but not to delete directories on the target that are peer to the intended directory. For example, using these source and target file structures:
Source on desktop:
~/
Money/
... (4 Replies)
Discussion started by: JavaMeister
4 Replies
LEARN ABOUT DEBIAN
iscsi_initiator
ISCSI_INITIATOR(4) BSD Kernel Interfaces Manual ISCSI_INITIATOR(4)NAME
iscsi_initiator -- kernel driver for the iSCSI protocol
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device iscsi_initiator
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
iscsi_initiator_load="YES"
DESCRIPTION
The iscsi_initiator implements the kernel side of the Internet SCSI (iSCSI) network protocol standard. The userland companion is
iscontrol(8), and permits access to remote virtual SCSI devices via cam(4).
SYSCTL VARIABLES
debug.iscsi_initiator set the debug-level, 0 means no debugging, 9 for maximum.
net.iscsi.isid the initiator part of the Session Identifier.
The following are informative only:
net.iscsi.driver_version the current version of the driver.
net.iscsi.sessions the number of current active sessions.
net.iscsi.n.targetname the target name of session n.
net.iscsi.n.targedaddress the IP address of the target of session n.
net.iscsi.n.stats statistics for session
net.iscsi.n.pid the process id of the userland side of session n, see iscontrol(8).
FILES
The iscsi_initiator driver creates the following:
/dev/iscsi used to create new sessions.
/dev/iscsi%d for each new session.
SEE ALSO cam(4), camcontrol(8), iscontrol(8)STANDARDS
iSCSI RFC 3720
BUGS
The lun discovery method is old-fashioned.
BSD May 9, 2010 BSD