Sponsored Content
Operating Systems Solaris Sun V445 hangs before {0} ok prompt Post 302878998 by hicksd8 on Tuesday 10th of December 2013 04:38:03 AM
Old 12-10-2013
The main part of the output that you posted is from the system controller (a Linux based appliance that underlies and controls the SPARC machine). The boot up from the SC that you posted finds no hardware errors and says "POST Passed all devices".

My thoughts are that:

1. It could still be a hardware fault but I think that unlikely given the "POST Passed all devices" message.
2. The "Host System has reset" message indicates the start of the SPARC boot process but it's possible that shortly after that console output is switched elsewhere due to a configuration setting on the ALOM.

https://www.unix.com/solaris/228271-alom-console-3.html

Suggest that you check that out first and post back any progress or lack of.

Last edited by hicksd8; 12-10-2013 at 05:44 AM..
 

9 More Discussions You Might Find Interesting

1. Solaris

Jumpstart Solaris 8 on Sun Blade 150 Hangs

We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there. We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies

2. Solaris

How to get to a OK prompt on new SUN T5140

Hi, I have a brand new SUN T5140 machine. I am trying to install Solaris 10 on the box. When I go to the machine using a KVM session I can see a blank screen , how can I get to the OK prompt to start the installation. Thanks, Suresh (10 Replies)
Discussion started by: gunnervarma
10 Replies

3. Solaris

How to get to the OK prompt without Sun keyboard

Hi all, I have just replaced the HDD on a Ultra 5 Spark machine, now I need to reinstall Solaris 9. The problem is: how do I get to the OK prompt without a Sun keyboard in order to boot from CD? At moment when I power on the machine I get the following error: Timeout Waiting for ARP/RARP... (13 Replies)
Discussion started by: sspirito
13 Replies

4. Solaris

XSCF prompt disappeared, Sun M5000

Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out. exit rebootxscf logout #. #> #> ~# ~# exit sendbreak exit I tried to set the Mode Switch to the service... (3 Replies)
Discussion started by: aixlover
3 Replies

5. Solaris

V445 unable to boot because of an error

This is what is displayed on the screen as the system tries to boot and then hangs: 0>Test CPU(s)....Done 0>Interrupt Crosscall....| SC Alert: DHCP negotiation failed, perhaps misconfigured or no DHCP server avail able Done 0>Init Memory....| SC Alert: Host System has Reset 'Done 0>PLL... (2 Replies)
Discussion started by: kenosongo
2 Replies

6. Solaris

Failure to boot v445

Hi Guys, I have a small problem with a v445 which I have been informed will only boot with the reconfigure option enabled. It is attached to HP SAN storage using qla2300 FCA's with a Veritas encapsulated rootvoldg (No Laughing here please) when I try a reboot I get the following error. ... (5 Replies)
Discussion started by: gull04
5 Replies

7. Solaris

Unable to move from rsc prompt to ok prompt

Hi, on sunfire v890 unable to move from rsc prompt to ok prompt, i have executed the command break. (9 Replies)
Discussion started by: manoj.solaris
9 Replies

8. Solaris

Rebuild/Reset to default Sun v445

Hello, I'm quite new to Unix but I've got an old Sun v445 server that was previously used as a backup database server, these have since been moved to new hardware. The old admin who configured the box has since retired and left no notes about it, so i have no idea what the root password is and... (2 Replies)
Discussion started by: dbajtr
2 Replies

9. Solaris

Install ext DLT Sun Tape drive on V445 Solaris 10

I have a SunFire V445 running Solaris 10 and am adding a Sun DLT tape drive. From the OK prompt the probe-scsi-all does see the drive and it is the proper target of 4. When I do the boot -- -r it does build the /dev/rmt directories correctly and the links to /devices appear correct as well. When I... (8 Replies)
Discussion started by: chastings
8 Replies
httppower(8)							     powerman							      httppower(8)

NAME
httppower - communicate with HTTP based power distribution units SYNOPSIS
httppower [--url URL] DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac- tively by the powerman daemon. OPTIONS
-u, --url URL Set the base URL. INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt: auth user:pass Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password over the network in plain text. seturl URL Set the base URL. Overrides the command line option. get [URL-suffix] Send an HTTP GET to the base URL with the optional URL-suffix appended. post [URL-suffix] key=val[&key=val]... Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument. FILES
/usr/sbin/httppower /etc/powerman/powerman.conf ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms of the GNU GPL. SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7). http://sourceforge.net/projects/powerman powerman-2.3.5 2009-02-09 httppower(8)
All times are GMT -4. The time now is 03:10 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy