One should assure that *.msg is a file:
There are 4 ways of using grep:
returns the matching lines.
returns the matching file names.
returns file name and matching line, separated by :
returns matching lines then the file name.
Hello,
I create a file touch 1201093003 fichcomp
and inside a repertory (which hava a lot of files) I want to list all files created before this file :
find *.* \! -maxdepth 1 - newer fichcomp but this command returned bash: /usr/bin/find: Argument list too long
but i make a filter all... (1 Reply)
Yes , I have to find a file in unix without using any find or where commands.Any pointers for the same would be very helpful as i am beginner in shell scritping and need a solution for the same.
Thanks in advance.
Regards
Jatin Jain (10 Replies)
I need to find whether there is a file named vijay is there or not in folder named "opt" .I tried "ls *|grep vijay" but it showed permission problem.
so i need to use find command (6 Replies)
I am using csh and getting the error "find: No match." but I cannot figure out why. What I am trying to do is set the find command to a variable and then execute the variable as a command. I ran it through a debugger and it looks like $FIND is getting set but the find command can not actually be... (2 Replies)
Hello everyone,
first post here, trying to learn scripting on my own and this forum as been really helpful so far. I made few little scripts working great but I m facing some problems with RE.
I have a bunch of files in many subdirectories called *001.ext *002.ext OR simple *.ext or *01.ext... (7 Replies)
Hi all ,
I'm new to unix
I have a checked project , there exists a file called xxx.config .
now my task is to find all the files in the checked out project which references to this xxx.config file.
how do i use grep or find command . (2 Replies)
Hello,
I am running some performance based tests on Solaris, and I was wondering how fast the "seeking" rate of Solaris is, or how fast Solaris can get information about files with the "find" command. Does anyone know what 'find' command I could run to traverse through my system to see the rate... (1 Reply)
Discussion started by: bstring
1 Replies
LEARN ABOUT HPUX
sendfiles
SENDFILES(1) [nmh-1.5] SENDFILES(1)NAME
sendfiles - send multiple files via a MIME message
SYNOPSIS
sendfiles [delay] mailpath subject file1 [file2 ...]
DESCRIPTION
The shell script sendfiles, is used to send a collection of files and directories via electronic mail.
sendfiles mailpath "subject" files ...
sendfiles will archive the files and directories you name with the tar command, and then mail the compressed archive to the "mailpath" with
the given "subject". The archive will be automatically split up into as many messages as necessary in order to get past most mailers.
Sometimes you want sendfiles to pause after posting a partial message. This is usually the case when you are running sendmail and expect
to generate a lot of partial messages. If the first argument given to sendfiles starts with a dash, then it is interpreted as the number
of seconds to pause in between postings, e.g.,
sendfiles -30 mailpath "subject" files ...
will pause 30 seconds in between each posting.
Extracting the Received Files
When these messages are received, invoke mhstore once for the list of messages. The default is for mhstore to store the combined parts as
a new message in the current folder, although this can be changed using storage formatting strings. You can then use mhlist to find out
what's inside; possibly followed by mhstore again to write the archive to a file where you can subsequently uncompress and untar it. For
instance:
% mhlist 5-8
msg part type/subtype size description
5 message/partial 47K part 1 of 4
6 message/partial 47K part 2 of 4
7 message/partial 47K part 3 of 4
8 message/partial 18K part 4 of 4
% mhstore 5-8
reassembling partials 5,6,7,8 to folder inbox as message 9
% mhlist -verbose 9
msg part type/subtype size description
9 application/octet-stream 118K
(extract with uncompress | tar xvpf -)
type=tar
conversions=compress
% mhstore 9
% uncompress < 9.tar.Z | tar xvpf -
Alternately, by using the -auto switch, mhstore will automatically do the extraction for you:
% mhlist 5-8
msg part type/subtype size description
5 message/partial 47K part 1 of 4
6 message/partial 47K part 2 of 4
7 message/partial 47K part 3 of 4
8 message/partial 18K part 4 of 4
% mhstore 5-8
reassembling partials 5,6,7,8 to folder inbox as message 9
% mhlist -verbose 9
msg part type/subtype size description
9 application/octet-stream 118K
(extract with uncompress | tar xvpf -)
type=tar
conversions=compress
% mhstore -auto 9
-- tar listing appears here as files are extracted
As the second tar listing is generated, the files are extracted. A prudent user will never put -auto in the .mh_profile file. The correct
procedure is to first use mhlist to find out what will be extracted. Then mhstore can be invoked with -auto to perform the extraction.
FILES
$HOME/.mh_profile The user profile
PROFILE COMPONENTS
Path: To determine the user's nmh directory
Current-Folder: To find the default current folder
SEE ALSO mhbuild(1), mhlist(1), mhshow(1), mhstore(1). Proposed Standard for Message Encapsulation (RFC-934)
DEFAULTS
`-noverbose'
CONTEXT
None
MH.6.8 11 June 2012 SENDFILES(1)