I have found failed mpio path on AIX and enabled that failed path as below
Enabled failed path as below
However it goes Enabled, but a few minutes later shows Failed ,could some one help me on this.
Please let me know above steps, if i miss anything and why it has failed.
Last edited by zaxxon; 11-18-2013 at 01:01 PM..
Reason: no, not the whole post in code tags, thats not the what they are for....
We are looking at running MPIO for it's redundancy and load balancing benefits. Does anyone know what pieces of software or modules are needed on the VIO server to get load balancing to work. Remember we are using EMC's DMX3500 storage system. We no longer want to use Powerpath. :rolleyes: ... (2 Replies)
Hi All,
The path requires me to go Single User mode. On single user mode, the patch still won't continue:
dhcpagent supports a new keyword in /etc/default/dhcpagent.
Please merge the existing /etc/default/dhcpagent with the
patched version of /etc/default/dhcpagent shipped with this... (2 Replies)
Hi folks,
does anybody have a link to a documentation how to implement native MPIO on AIX? We are using EMC PowerPath and Datacore SanSymphony/Cambex for this so far and I wasn't able to find a good description on that topic. All I know so far is that mkpath, chpath and lspath are used to... (3 Replies)
Hello All,
After creating lpp_source/spot from AIX 5.3TL6-07 DVD on the NIM(AIX6.1), I went online and download the fix pack for reaching TL8-04. (it was less than 200Mgegs total)
then I did define a newer lpp_source530TL8-04 via a copy from the older lpp_source530TL6-07 (I diduse a command... (2 Replies)
On a particular LPAR, I was running AIX 5.3 TL 3. On Monday I did an update of the LPAR to 5.3 TL 9 SP2. The install was smooth, but then I ran into a problem.
The MPIO driver does not work with LSI's StoreAge (SVM4). I did some looking, and looks like
5.3 TL3 = IBM.MPIO 5.3.0.30
5.3... (0 Replies)
Hi,
we have a vew boxes using MPIO and they are connected to some virtualization software managing some disk subsystems, offering volumes to the AIX boxes.
Sometimes when a cable has been plugged out for a test or when a real problem occurs, using lspath to show the state of the paths shows... (8 Replies)
Hello,
we are planning to deploy some of our databases on AIX/LPAR based servers (we didn't bought it yet ...). IBM's engineers says that if we want to boot them from SAN the hardware array has to be compatible with MPIO but they don't want to deliver any document with list of arrays supported... (5 Replies)
This is getting very confusing for me, and appreciate if someone can help.
Platform: Power VM ( Virtual I/O Server)
ioslevel 2.1.3.10-FP23
# oslevel -s
6100-05-00-0000
Storage: IBM DS4300
Two HBAs - Dual Port Fibre Adapter Channels
Each card has two ports , so a total of 4 ports going... (3 Replies)
Hello,
I have some concerns over the disk management of my AIX system.
For example server1
/ > lspv
hdisk0 00fa6d1288c820aa rootvg active
hdisk1 00fa6d1288c8213c vg_2 active
hdisk2 00c1cc14d6de272b ... (6 Replies)
Hello,
I have encountered the issue on my AIX 6.1. As you can see below, the hdisk1 & hdisk8 are not recognized by the system
/ > lspv
hdisk0 00fa6d1288c820aa rootvg active
hdisk1 00fa6d1288c8213c None
hdisk2 ... (9 Replies)
Discussion started by: Phat
9 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)