Hi all,
I tried to use this command
ndd -set /dev/eri adv_1000fdx_cap 1
but i get a "operation failed, Invalid argument"
anyone can help ? Thanks (5 Replies)
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Hello all,
I`ve the following problem - I cannot start inetd in any way possible:
bash-3.00# svcs inetd
STATE STIME FMRI
offline Jul_30 svc:/network/inetd:default
bash-3.00#
bash-3.00# svcadm enable -r inetd
bash-3.00# svcs inetd
STATE STIME FMRI... (6 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
I'm trying to migrate a Solaris 10 flar archive from a Sun M3000 to a T4-1. When I first created the zone I followed the Oracle instructions here: Transitioning an Oracle Solaris 10 Instance to an Oracle Solaris 11 System - Transitioning From Oracle Solaris 10 to Oracle Solaris 11 That worked... (6 Replies)
Discussion started by: Michele31416
6 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)