Sponsored Content
Special Forums Hardware How to test the speed of your WIFI network? Post 302869619 by lupin..the..3rd on Wednesday 30th of October 2013 03:58:19 PM
Old 10-30-2013
The speed is going to vary greatly depending on the distance between the laptop and the wifi access point, and also on what is between the laptop and the wifi access point (walls, floors, etc.)

Wifi is pretty clever, it will adjust the transmission rate dynamically to adapt to changing signal conditions. Any measurements you take will be relevant only to that specific laptop location; i.e. if you move the laptop, even just a few feet, you may see different results.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Speed of network link

Sorry to keep bothering you guys like this with all these boring, related questions. But here's one that should be more readily answerable. What command or file should i use to get the speed/data rate of a network link? This is the capacity speed for instance 10Mbps or 100 Mbps in the case of the... (2 Replies)
Discussion started by: mint1981
2 Replies

2. UNIX for Advanced & Expert Users

network speed is slow

Hello, everyone: i encounter a problem these days , pls help me ,thanks in advance. my env: machine: ES40 A ES40 B os: true64 Unix 4.0f note: src.tar 8M network card speed 100M my problem: ... (3 Replies)
Discussion started by: q30
3 Replies

3. HP-UX

Network speed on HPUX

Hello, can anyone tell me how to change network speed or duplex speed...don't understand the concept why that is imp when the server comes back up to check up on it. Basically have to make sure that the setting from the orginial speed. (2 Replies)
Discussion started by: catwomen
2 Replies

4. IP Networking

network speed not tale with the port setting

Hi all, one of my Sun Box facing the problem. The network port i had set to Auto-Negotiated and i had edited the /etc/system/ file in the Sun box as below: set hme:hme_adv_autoneg_cap=1 set hme:hme_adv_100fdx_cap=0 set hme:hme_adv_100hdx_cap=0 But when i checked the /var/adm/messages/, it... (0 Replies)
Discussion started by: AirWalker83
0 Replies

5. Solaris

Change speed on network card

I recently learned that Sun Solaris network cards (ce devices) have problems with ndd -get commands. I did some searching and found out about the netstat -k command to show me the link speed. What is the best way to change the link speed (both one time and permanently)? I am running Solaris 9... (7 Replies)
Discussion started by: hshapiro
7 Replies

6. UNIX for Advanced & Expert Users

speed test +20,000 file existance checks too slow

Need to make a very fast file existence checker. Passing in 20-50K num of files In the code below ${file} is a file with a listing of +20,000 files. test_speed is the script. I am commenting out the results of <time test_speed try>. The normal "test -f" is much much too slow when a system... (2 Replies)
Discussion started by: nullwhat
2 Replies

7. Solaris

network speed

i have first server (sun solaris 5.10) for example X(172.x.x.x) and i have second server (sun solaris 5.10) for example Y(192.x.x.x) also we have 3 clients PC (windows XP)(172.x.x.x) the X server connect to Y server and to clients PC * who to know the network speed between X and Y * who to... (1 Reply)
Discussion started by: anwar
1 Replies

8. UNIX for Dummies Questions & Answers

how to see network speed of virtual linux machine?

After installing PV (Para virtual drivers) drivers I m not able to check the network speed of my Ethernet port. Please check the output of mii-tool and ethtool. # mii-tool eth0 SIOCGMIIPHY on 'eth0' failed: Operation not supported # ethtool eth0 Settings for eth0: Link... (2 Replies)
Discussion started by: pinga123
2 Replies

9. High Performance Computing

IBM Hardware: Test speed of an execution core reliably.

Hey Folks, Doing simple floating point or integer arithmetic is limited since if another execution core is not busy, the system will (presumably?) assign CPU resources to where they are needed so I could be getting the performance of 2 or more cores theoretically? Any good reliable way to... (2 Replies)
Discussion started by: Devyn
2 Replies

10. Red Hat

Local Network Speed

Dear All, I have an intel NUC running CentOS 7 and physically connected to my Netgear CBVG834G router. They both have Gigabit Ethernet cards and supposedly a top notch network cable connecting the two devices. But when I run ethtool the connection is only running at 100Mbit/s What can I do... (3 Replies)
Discussion started by: freddie50
3 Replies
LM-PROFILER(8)						      System Manager's Manual						    LM-PROFILER(8)

NAME
/usr/sbin/lm-profiler - laptop mode profiler SYNOPSIS
/usr/sbin/lm-profiler DESCRIPTION
This manual page documents briefly the /usr/sbin/lm-profiler command. lm-profiler is a tool for profiling disk operations. It is a part of laptop mode tools and is useful only in relation to rest of laptop mode tools. It helps you to detect programs and services that use up system resources and that cause disk activity, and it allows you to disable them when laptop mode is active. When you start lm-profiler, it will execute a "profiling run", which can take some time. Start lm-profiler when you are working on batter- ies, preferably, because that will allow it to analyze the actual situation that it is supposed to optimize. During the profiling run, you can use your system normally; however, any disk activity caused by your actions will end up in the profiler's results. When the profiling run is finished, you will be presented with a list of programs that deserve your attention, either because they listen on a network (which is not usually useful when you are working offline) or because they caused disk activity in a disk-spindown-unfriendly pattern. When lm- profiler can guess an init script that belongs to a program, it presents you with the opportunity to disable the program when you are work- ing on battery. It does this by placing a link to the init script in /etc/laptop-mode/batt-stop. Any programs that lm-profiler cannot find an init script for is simply reported, so that you can stop the program manually if you want to. WARNING ABOUT DISABLING PROGRAMS: It may not be safe to disable some programs. They may be needed for proper operation of your system. Dis- able services only if you know what they do and why you don't need them. FILES
/etc/lm-profiler.conf lm-profiler retrieves its profiling rules from this file. SEE ALSO
lm-profiler.conf(8). laptop-mode.conf(8). daemons.conf(8). AUTHOR
This manual page was written by Bart Samwel (bart@samwel.tk) and Jan Polacek (jerome@ucw.cz) for the Debian system (but may be used by oth- ers). Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 any later version published by the Free Software Foundation. On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL. LM-PROFILER(8)
All times are GMT -4. The time now is 03:25 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy