10-29-2013
The config looks good from what I can see... can you provide a prtvtoc output for both disks? also, how are the disks mirrored? and yes, the solaris version (cat /etc/release)would also be good info!
9 More Discussions You Might Find Interesting
1. Solaris
I had installed solaris 10 on 440 on disk 0. I had done ufsrestore on disk1 from tape and then rebooted
Rebooting with command: boot disk1
Boot device: /pci@1f,700000/scsi@2/disk@1,0 File and args:
SunOS Release 5.10 Version Generic_118833-24 64-bit
Copyright 1983-2006 Sun Microsystems,... (3 Replies)
Discussion started by: vr76413
3 Replies
2. Solaris
Hi All,
We had a Sun Netra T1 go down the other day, the root disk was mirrored using vxvm. Upon boot from either disk, we had the following error appear:
WARNING: Error writing ufs log state
WARNING: ufs log for / changed state to Error
WARNING: Please umount(1M) / and run... (4 Replies)
Discussion started by: badoshi
4 Replies
3. Red Hat
Hello,
I have a test PC running Fedora 10. Friday evening it was working fine, I have some perl scripts which are scheduled to run every morning.
But when I started work this morning, I found I cannot ping the machine. When I switched on the monitor, I saw the GRUB promt :(. I am not sure... (10 Replies)
Discussion started by: SivaramaRaju
10 Replies
4. Hardware
Hey All,
Im using Fedora 2.6 (which is cannot be changed for compatibility reasons).
I cloned a drive from a different server and when i added this drive to a new box, during startup it hangs on "Configuring Kernel Parameters:"
Is there any way to bypass this process and still boot... (0 Replies)
Discussion started by: robfwauk
0 Replies
5. Fedora
hello everyone,
I have Matlab installed on Fedora 16. I tried running it by simply typing on terminal:
$ matlabBut it returned the follwoing error:
--- can anyone suggest a solution?
cheers,
peter
---------- Post updated at 10:57 PM ---------- Previous update was at 10:54 PM ----------... (1 Reply)
Discussion started by: peter_071
1 Replies
6. Solaris
Hi,
Can you help me on booting x86 server configured under VxVM. Server boots fine normally from both the disks but if I try to boot server from mirror disk without starting veritas, then it does not boot.
vxplex -g rootdg dis var-02
vxplex -g rootdg dis swapvol-02
vxplex -g rootdg dis... (2 Replies)
Discussion started by: milindphanse604
2 Replies
7. Solaris
Hi Solaris 10 Experts,
I am wondering what is the correct syntax to edit in Grub when trying to specify the local ZFS boot disk while booting up from a Solaris 10 x86 64bits DVD installation disk. In other word, I try to boot up from local disk without removing the Solaris installation disk... (0 Replies)
Discussion started by: gjackson123
0 Replies
8. Solaris
Hi,
I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
2 Replies
9. Red Hat
Hi,
I just P2V an old machine running Redhat 5.5 on a physical server. After P2V was completed, when boot up it got an error. Please refer to the attachment for the error. Please assist. Thanks. (2 Replies)
Discussion started by: freshmeat
2 Replies
CCD(4) BSD Kernel Interfaces Manual CCD(4)
NAME
ccd -- Concatenated disk driver
SYNOPSIS
pseudo-device ccd [count]
DESCRIPTION
The ccd driver provides the capability of combining one or more disks/partitions into one virtual disk.
This document assumes that you're familiar with how to generate kernels, how to properly configure disks and pseudo-devices in a kernel con-
figuration file, and how to partition disks.
Note that the 'raw' partitions of the disks must not be combined. Each component partition should be offset at least one cylinder from the
beginning of the component disk. This avoids potential conflicts between the component disk's disklabel and the ccd's disklabel. The kernel
will only allow component partitions of type FS_CCD. But for now, it allows partition of all types since some port lacks support of an on-
disk BSD disklabel. The partition of FS_UNUSED may be rejected because device driver of component disk will refuse it.
In order to compile in support for the ccd, you must add a line similar to the following to your kernel configuration file:
pseudo-device ccd 4 # concatenated disk devices
The count argument is how many ccds memory is allocated for at boot time. In this example, no more than 4 ccds may be configured.
A ccd may be either serially concatenated or interleaved. To serially concatenate the partitions, specify the interleave factor of 0.
If a ccd is interleaved correctly, a ``striping'' effect is achieved, which can increase performance. Since the interleave factor is
expressed in units of DEV_BSIZE, one must account for sector sizes other than DEV_BSIZE in order to calculate the correct interleave. The
kernel will not allow an interleave factor less than the size of the largest component sector divided by DEV_BSIZE.
Note that best performance is achieved if all component disks have the same geometry and size. Optimum striping cannot occur with different
disk types.
Also note that the total size of concatenated disk may vary depending on the interleave factor even if the exact same components are concate-
nated. And an old on-disk disklabel may be read after interleave factor change. As a result, the disklabel may contain wrong partition
geometry and will cause an error when doing I/O near the end of concatenated disk.
There is a run-time utility that is used for configuring ccds. See ccdconfig(8) for more information.
WARNINGS
If just one (or more) of the disks in a non-mirrored ccd fails, the entire file system will be lost.
FILES
/dev/{,r}ccd* ccd device special files.
SEE ALSO
config(1), MAKEDEV(8), ccdconfig(8), fsck(8), mount(8), newfs(8)
HISTORY
The concatenated disk driver was originally written at the University of Utah.
BSD
March 5, 2004 BSD