Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2.
also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive... (4 Replies)
All
I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any... (1 Reply)
Hi,
I`m on SunFire480R with Solaris 10. Disk in rootdg group failed, so it was replaced. However, I cannot make Veritas initalise the replaced disk:
# vxdctl enable
# vxdisk list c1t0d0s2
Device: c1t0d0s2
devicetag: c1t0d0
type: auto
flags: online error private autoconfig... (1 Reply)
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given... (5 Replies)
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
LEARN ABOUT POSIX
grub
GRUB(8) FSF GRUB(8)NAME
grub - the grub shell
SYNOPSIS
grub [OPTION]...
DESCRIPTION
Enter the GRand Unified Bootloader command shell.
--batch
turn on batch mode for non-interactive use
--boot-drive=DRIVE
specify stage2 boot_drive [default=0x0]
--config-file=FILE
specify stage2 config_file [default=/boot/grub/menu.lst]
--device-map=FILE
use the device map file FILE
--help display this message and exit
--hold wait until a debugger will attach
--install-partition=PAR
specify stage2 install_partition [default=0x20000]
--no-config-file
do not use the config file
--no-curses
do not use curses
--no-floppy
do not probe any floppy drive
--no-pager
do not use internal pager
--preset-menu
use the preset menu
--probe-second-floppy
probe the second floppy drive
--read-only
do not write anything to devices
--verbose
print verbose messages
--version
print version information and exit
REPORTING BUGS
Report bugs to <bug-grub@gnu.org>.
SEE ALSO update-grub(8), grub-install(8).
The full documentation for grub is maintained as a Texinfo manual in the grub-legacy-doc package. If the info and grub programs are prop-
erly installed at your site, the command
info grub
should give you access to the complete manual.
grub (GNU GRUB 0.97) January 2013 GRUB(8)