Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2.
also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive... (4 Replies)
All
I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any... (1 Reply)
Hi,
I`m on SunFire480R with Solaris 10. Disk in rootdg group failed, so it was replaced. However, I cannot make Veritas initalise the replaced disk:
# vxdctl enable
# vxdisk list c1t0d0s2
Device: c1t0d0s2
devicetag: c1t0d0
type: auto
flags: online error private autoconfig... (1 Reply)
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given... (5 Replies)
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
LEARN ABOUT POSIX
findfs
FINDFS(8) System Administration FINDFS(8)NAME
findfs - find a filesystem by label or UUID
SYNOPSIS
findfs NAME=value
DESCRIPTION
findfs will search the block devices in the system looking for a filesystem or partition with specified tag. The currently supported tags
are:
LABEL=<label>
Specifies filesystem label.
UUID=<uuid>
Specifies filesystem UUID.
PARTUUID=<uuid>
Specifies partition UUID. This partition identifier is supported for example for GUID Partition Table (GPT) partition tables.
PARTLABEL=<label>
Specifies partition label (name). The partition labels are supported for example for GUID Partition Table (GPT) or MAC partition
tables.
If the filesystem or partition is found, the device name will be printed on stdout.
The complete overview about filesystems and partitions you can get for example by
lsblk --fs
partx --show <disk>
blkid
EXIT STATUS
0 success
1 label or uuid cannot be found
2 usage error, wrong number of arguments or unknown option
AUTHOR
findfs was originally written by Theodore Ts'o <tytso@mit.edu> and re-written for the util-linux package by Karel Zak <kzak@redhat.com>.
ENVIRONMENT
LIBBLKID_DEBUG=all
enables libblkid debug output.
SEE ALSO blkid(8), lsblk(8), partx(8)AVAILABILITY
The findfs command is part of the util-linux package and is available from Linux Kernel Archive <https://www.kernel.org/pub/linux/utils
/util-linux/>.
util-linux March 2014 FINDFS(8)