10-29-2013
have you ever tried #ifconfig eth0 <ip> up
Try this.... It will up the interface and allocate ip for that.....
10 More Discussions You Might Find Interesting
1. IP Networking
Hi there,
I got a problem with my linux eth0.
It worked well, just one day when i boot it, "Failed" to be active.
The eth0 is inactive! I tried to use KDE network configuration tool to add the type of the eth card, I can't make it active. It gave me warning of "the eth card can't be... (1 Reply)
Discussion started by: gusla
1 Replies
2. IP Networking
Hi there guys!
I have a small task that I have to accomplish, but I don't seem to be able to do that.
I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies
3. UNIX for Dummies Questions & Answers
Hi,
We have dual processor dell machine loaded with redhat linux 7.2. It was working fine without any problem but recently power went off so suddenly system switched off. From then onwards system is running very slow. My suspect is on processor. How to check both the processors running properly or... (8 Replies)
Discussion started by: bache_gowda
8 Replies
4. Ubuntu
Greetings,
I have installed a Ubuntu server and attempting put a static IP address on interface ETH0. I edited the /etc/network/interfaces with the following:
auto eth0
iface eth0 inet static
address 192.168.203.270
gateway 192.168.203.1
netwask 255.255.255.0
network 192.168.0.0... (2 Replies)
Discussion started by: jroberson
2 Replies
5. Red Hat
hi
Recently the above option has stopped working all together. On clicking on this option it appears as though the window will open as the outline of the box appears but nothing more.
On running this from a command prompt within the GUI , I get the following error:
The last line... (0 Replies)
Discussion started by: timcs
0 Replies
6. UNIX for Dummies Questions & Answers
Hi,
Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
7. Red Hat
Issue:crond is running, can even restart it and /var/log/cron shows it starting. The /etc/crontab file is correct as compared to another machine. I set the crontab file to enter a datestamp into a file under /tmp every minute. Thing is, the crontab file is not being read or cron is not working... (12 Replies)
Discussion started by: robjmarquez
12 Replies
8. Red Hat
Hi,
I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine.
I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows:
Settings for eth0:
Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies
9. Red Hat
Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this.
when i'm trying to load/add qeth driver . The driver is not found showing this message.
Bash: lsmod | grep qeth
Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies
10. IP Networking
Hi all,
I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic.
I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies
LEARN ABOUT DEBIAN
if_edsc
EDSC(4) BSD Kernel Interfaces Manual EDSC(4)
NAME
edsc -- Ethernet discard network interface
SYNOPSIS
device edsc
DESCRIPTION
The edsc interface is a software discard mechanism which may be used for performance analysis and software testing. It imitates an Ethernet
device, which allows for its use in conjunction with such drivers as if_bridge(4) and vlan(4).
As with other network interfaces, an edsc interface must have network addresses assigned for each address family with which it is to be used.
These addresses may be set or changed with the SIOCSIFADDR ioctl(2) or ifconfig(8) utility.
Each edsc interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the
cloned_interfaces variable in rc.conf(5).
SEE ALSO
ioctl(2), arp(4), if_bridge(4), inet(4), intro(4), vlan(4), rc.conf(5), arp(8), ifconfig(8)
HISTORY
The edsc device was derived from the disc(4) device and first appeared in FreeBSD 6.3. This manpage was adapted from disc(4).
CAVEATS
Since outgoing packets are just discarded by edsc, ARP requests stay unreplied. Consequently, an IP packet cannot be sent via edsc until a
static arp(4) entry is created for its next hop using arp(8).
Initially an edsc interface has a zero link level address. It can be changed with ifconfig(8) lladdr if needed.
BSD
March 25, 2007 BSD