Sponsored Content
Operating Systems Linux Red Hat Eth0 not running in redhat 6.4 Post 302868847 by vamshigvk475 on Tuesday 29th of October 2013 03:08:16 AM
Old 10-29-2013
have you ever tried #ifconfig eth0 <ip> up

Try this.... It will up the interface and allocate ip for that.....
 

10 More Discussions You Might Find Interesting

1. IP Networking

Linux eth0 incative

Hi there, I got a problem with my linux eth0. It worked well, just one day when i boot it, "Failed" to be active. The eth0 is inactive! I tried to use KDE network configuration tool to add the type of the eth card, I can't make it active. It gave me warning of "the eth card can't be... (1 Reply)
Discussion started by: gusla
1 Replies

2. IP Networking

Adding an IP to eth0

Hi there guys! I have a small task that I have to accomplish, but I don't seem to be able to do that. I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies

3. UNIX for Dummies Questions & Answers

How to check both the processores running or not in redhat linux

Hi, We have dual processor dell machine loaded with redhat linux 7.2. It was working fine without any problem but recently power went off so suddenly system switched off. From then onwards system is running very slow. My suspect is on processor. How to check both the processors running properly or... (8 Replies)
Discussion started by: bache_gowda
8 Replies

4. Ubuntu

Trying to config eth0 - Ubuntu

Greetings, I have installed a Ubuntu server and attempting put a static IP address on interface ETH0. I edited the /etc/network/interfaces with the following: auto eth0 iface eth0 inet static address 192.168.203.270 gateway 192.168.203.1 netwask 255.255.255.0 network 192.168.0.0... (2 Replies)
Discussion started by: jroberson
2 Replies

5. Red Hat

Problems running redhat config samba in the GUI

hi Recently the above option has stopped working all together. On clicking on this option it appears as though the window will open as the outline of the box appears but nothing more. On running this from a command prompt within the GUI , I get the following error: The last line... (0 Replies)
Discussion started by: timcs
0 Replies

6. UNIX for Dummies Questions & Answers

how can I find which one is eth0?

Hi, Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0? Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies

7. Red Hat

redhat 5.2 tikanga crond running but not reading crontab file

Issue:crond is running, can even restart it and /var/log/cron shows it starting. The /etc/crontab file is correct as compared to another machine. I set the crontab file to enter a datestamp into a file under /tmp every minute. Thing is, the crontab file is not being read or cron is not working... (12 Replies)
Discussion started by: robjmarquez
12 Replies

8. Red Hat

Eth0 Limitations

Hi, I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine. I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows: Settings for eth0: Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies

9. Red Hat

Not showing ifcfg eth0....redhat enterprise Linux 6.2

Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this. when i'm trying to load/add qeth driver . The driver is not found showing this message. Bash: lsmod | grep qeth Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies

10. IP Networking

iptables On for eth0 and off for other interfaces

Hi all, I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic. I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies
Mirror/redirect action in tc(8)                                        Linux                                       Mirror/redirect action in tc(8)

NAME
mirred - mirror/redirect action SYNOPSIS
tc ... action mirred DIRECTION ACTION [ index INDEX ] dev DEVICENAME DIRECTION := { ingress | egress } ACTION := { mirror | redirect } DESCRIPTION
The mirred action allows packet mirroring (copying) or redirecting (stealing) the packet it receives. Mirroring is what is sometimes referred to as Switch Port Analyzer (SPAN) and is commonly used to analyze and/or debug flows. OPTIONS
ingress egress Specify the direction in which the packet shall appear on the destination interface. mirror redirect Define whether the packet should be copied (mirror) or moved (redirect) to the destination interface. index INDEX Assign a unique ID to this action instead of letting the kernel choose one automatically. INDEX is a 32bit unsigned integer greater than zero. dev DEVICENAME Specify the network interface to redirect or mirror to. EXAMPLES
Limit ingress bandwidth on eth0 to 1mbit/s, redirect exceeding traffic to lo for debugging purposes: # tc qdisc add dev eth0 handle ffff: ingress # tc filter add dev eth0 parent ffff: u32 match u32 0 0 action police rate 1mbit burst 100k conform-exceed pipe action mirred egress redirect dev lo Mirror all incoming ICMP packets on eth0 to a dummy interface for examination with e.g. tcpdump: # ip link add dummy0 type dummy # ip link set dummy0 up # tc qdisc add dev eth0 handle ffff: ingress # tc filter add dev eth0 parent ffff: protocol ip u32 match ip protocol 1 0xff action mirred egress mirror dev dummy0 Using an ifb interface, it is possible to send ingress traffic through an instance of sfq: # modprobe ifb # ip link set ifb0 up # tc qdisc add dev ifb0 root sfq # tc qdisc add dev eth0 handle ffff: ingress # tc filter add dev eth0 parent ffff: u32 match u32 0 0 action mirred egress redirect dev ifb0 SEE ALSO
tc(8), tc-u32(8) iproute2 11 Jan 2015 Mirror/redirect action in tc(8)
All times are GMT -4. The time now is 02:06 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy