|
|
Sponsored Content
Operating Systems
Linux
Red Hat
Eth0 not running in redhat 6.4
Post 302866899 by cjashu on Tuesday 22nd of October 2013 10:29:17 PM
10-22-2013
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
Hi there,
I got a problem with my linux eth0.
It worked well, just one day when i boot it, "Failed" to be active.
The eth0 is inactive! I tried to use KDE network configuration tool to add the type of the eth card, I can't make it active. It gave me warning of "the eth card can't be... (1 Reply)
Discussion started by: gusla
1 Replies
2. IP Networking
Hi there guys!
I have a small task that I have to accomplish, but I don't seem to be able to do that.
I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies
3. UNIX for Dummies Questions & Answers
Hi,
We have dual processor dell machine loaded with redhat linux 7.2. It was working fine without any problem but recently power went off so suddenly system switched off. From then onwards system is running very slow. My suspect is on processor. How to check both the processors running properly or... (8 Replies)
Discussion started by: bache_gowda
8 Replies
4. Ubuntu
Greetings,
I have installed a Ubuntu server and attempting put a static IP address on interface ETH0. I edited the /etc/network/interfaces with the following:
auto eth0
iface eth0 inet static
address 192.168.203.270
gateway 192.168.203.1
netwask 255.255.255.0
network 192.168.0.0... (2 Replies)
Discussion started by: jroberson
2 Replies
5. Red Hat
hi
Recently the above option has stopped working all together. On clicking on this option it appears as though the window will open as the outline of the box appears but nothing more.
On running this from a command prompt within the GUI , I get the following error:
The last line... (0 Replies)
Discussion started by: timcs
0 Replies
6. UNIX for Dummies Questions & Answers
Hi,
Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
7. Red Hat
Issue:crond is running, can even restart it and /var/log/cron shows it starting. The /etc/crontab file is correct as compared to another machine. I set the crontab file to enter a datestamp into a file under /tmp every minute. Thing is, the crontab file is not being read or cron is not working... (12 Replies)
Discussion started by: robjmarquez
12 Replies
8. Red Hat
Hi,
I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine.
I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows:
Settings for eth0:
Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies
9. Red Hat
Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this.
when i'm trying to load/add qeth driver . The driver is not found showing this message.
Bash: lsmod | grep qeth
Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies
10. IP Networking
Hi all,
I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic.
I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies
LEARN ABOUT DEBIAN
aoe-interfaces
aoe-interfaces(8) System Manager's Manual aoe-interfaces(8) NAME
aoe-interfaces - restrict aoe driver to specified network interfaces SYNOPSIS
aoe-interfaces [dev1] [dev2 ...] aoe-interfaces -c DESCRIPTION
The aoe-interfaces command tells the aoe driver to ignore ATA over Ethernet (AoE) traffic on all but the specified network interfaces. It is analogous to the aoe_iflist module load option. If neither the aoe_iflist module load option nor the aoe-interfaces command are used, the aoe driver will use any network interface for AoE traffic. Using aoe-interfaces to limit AoE to only trusted networks prevents the case where a rogue AoE target appears on a public net- work, diverting data from the legitimate AoE target. Such an imposter target effectively corrupts the data on the legitimate target. If the aoe driver is a module, then calling aoe-interfaces without arguments will display the current interfaces list. If it hasn't been set then the output will be blank. It's good to run the aoe-discover command after setting the AoE interfaces list. OPTIONS
-c The -c flag will clear the interface access list, permitting any interface to be used. EXAMPLE
In this example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic. After remembering that shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then calls aoe-discover to ask the aoe driver to look for new AoE devices. nai:~# modprobe aoe aoe_iflist="eth0" nai:~# aoe-stat e10.9 eth0 up nai:~# aoe-interfaces eth0 eth3 nai:~# aoe-discover nai:~# aoe-stat e7.0 eth3 up e7.1 eth3 up e7.2 eth3 up e7.3 eth3 up e7.4 eth3 up e7.5 eth3 up e7.6 eth3 up e7.7 eth3 up e7.8 eth3 up e7.9 eth3 up e10.9 eth0 up nai:~# aoe-interfaces eth0 eth3 SEE ALSO
aoe-discover(8), aoe-stat(8), aoetools(8). AUTHOR
Ed L. Cashin (ecashin@coraid.com) aoe-interfaces(8)