How can I check how much space is left in the solaris file system? and how can I increase those space in the file system?. I am trying to install Oracle Database on Solaris 8.But, it keep giving me error message says that"There is not enough space on the volume you have specified".
Thanks
... (1 Reply)
Hi frnz,
Need an urgent help...
I have installed solaris 8 in a sunblade workstation with 136GB hdd.
While installation it has taken a default filesystem size as 1.37GB for root.
AFtr completing the installation i have extended the root partition to 130GB.
But still df output shows... (4 Replies)
Hi,
I try add a new file system:
#zfs create dsk1/mqm
it came back with:
#cannot create 'dsk1/mqm': no such pool 'dsk1'
what do I have to do?
Kind regards
Mehrdad (2 Replies)
Hi all,
we are usig aix 4.3 and i need to increase the size of "/u01" file sytem which is mounted on logical volume "lv00", but "/u01" file system size is 9 GB and logical volume "lvoo" size 9 GB.how do i increase the size of /u01.do i increase the size of logical volume "lv00" and then... (2 Replies)
Hello Admins,
I am running a redhat linux 5 on vmware workstation.
I need to increase or add some more space to my root (/) partition. I don't have any LVM configured..
Please suggest.
# df -kh
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 3.8G 3.1G ... (4 Replies)
Hi All,
I am using this commands to dynamically increase ZFS swap space on Solaris
my question is:
1- after i make these commands it will permanent or it will remove after restart
2- how to make it permanent
# swap -l
swapfile dev swaplo bloques libre
/dev/zvol/dsk/rpool/swap... (4 Replies)
Dear Friends,
I would like to increase the size of a file system from 10GB to 15GB.
System is runing on HP-UX 11.31.
Please help in the matter.
Regards,
Bhagawati Pandey (3 Replies)
Hi,
I came across a situation where I had to increase a filesystem that was 100% full and received this error:
/tmp:chfs -a size=+5000M /tmp
0516-634 lquerypv: /tmp directory does not have enough space,
delete some files and try again.
0516-788 extendlv: Unable to extend logical... (2 Replies)
Hi
I have the following file system, that needs to be expanded to more 500Gb, so a total of 1Tb:
df -h /oradata1
Filesystem Size Used Available Capacity Mounted on
oradata1 587G 517G 69G 89% /oradata1
I am not familiar with zfs, I am more... (17 Replies)
Discussion started by: fretagi
17 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)